Description

Furukawa Unic URW295CUR Operators Manual

If you’re running a Furukawa Unic URW295CUR mini-crawler crane on a job site, you already know the risk of tipping or overloading when you don’t have the right numbers in front of you. The Furukawa Unic URW295CUR Operators Manual is not a service manual—it’s the operation and safety bible that tells you how to set outriggers, read the rated load chart, and use the U-Wave radio remote without guessing. I’ve seen too many guys skip the setup steps and end up with a crane on its side. This 165-page book stops that.

165 Pages of Factory Crane Operation

Every page in this manual comes straight from Furukawa Unic Corporation in Tokyo. Page numbering starts at 0-1 and runs through the full 165 pages. Chapter 1 through 3 cover safety precautions for the carrier and crane—before, during, and after operation. Chapter 10 shows you how to operate the carrier, including how to crawl with the load. Chapter 11 walks through every crane control: derricking the boom, hoisting the hook, telescoping, slewing, and storing the crane. The radio remote control section (Chapter 12) details battery replacement and inspection procedures. Maintenance inspections are in Chapter 13, with intervals at 250 hours or 3 months.

Load Charts and Working Radius

Chapter 7 defines terms like net rated load, working radius, and boom angle. Chapter 8 gives you the working range chart and rated load chart. You need these charts to know whether you’re within the crane’s capacity for a given lift. The manual explains exactly how to reference them—no guesses, no shortcuts. If you’re setting up on uneven ground, you’ll use the outrigger setup procedures from Chapter 11, pages 11-3 through 11-6.

U-Wave Radio Remoto Control: Chapter 12

The URW295CUR uses a radio remote control system. Chapter 12 covers safety precautions for the transmitter, inspection before operation, and how to switch between manual operation mode and radio control mode. The manual walks you through battery replacement (page 12-34) and daily trouble checks (page 12-37). If you’ve ever had a remote drop out mid-lift, you know why having the factory procedure matters. The crane can be operated manually—similar to a Manual Transmission in a vehicle—or by radio remote. A Manual Transmission analogy only goes so far; the manual gives you the real steps.

Does This Manual Cover Maintenance?

Yes, but it’s limited to daily and 250-hour inspections for the carrier and crane. Chapter 13 details inspection before operation (page 13-2) and storage procedures. This is not a workshop manual with torque specs or overhaul procedures. For that, get the Furukawa URW295CUR URW295CAR Workshop Manual. If you need a different variant, check the Furukawa Unic URW295C1UR Operators Manual – Factory Specs or the Furukawa Unic URA343 URA344 URA345 Operators Manual – OEM Specs. Each manual is specific to the model and spec code.

Source Authenticity: Factory Print vs Aftermarket

This is an original Furukawa Unic publication, printed in Japan. The PDF is a direct scan of the factory document—no third-party rewrites, no missing pages. Aftermarket manuals often omit the name plate locations (Chapter 6) or the turn-over prevention device specs (Chapter 9). You get all 165 pages, including the setup of this manual page 0-4 and the full table of contents. I insist on OEM documentation for anything with a load chart. Copy-paste aftermarket garbage gets people hurt.

Does this Operators Manual include torque values or repair procedures?

No. This is an operators manual, not a service manual. It covers safe crane operation, load charts, radio remote procedures, and daily maintenance checks. No engine or hydraulic torque specs.

What serial numbers and spec codes are covered?

The manual applies to Furukawa Unic URW295CUR mini-crawler cranes with the specification and code number listed on the name plate. The name plate is located at the rear side of the column. If your crane has a different spec, verify the model and spec against the manual’s introduction page (0-1). Contact Furukawa Unic if you need confirmation for a specific serial number range.

Don’t operate a crane with a missing or generic manual. The cost of a lift failure is way higher than the price of this PDF. Access the Factory Manual now and keep it on your tablet or print it for the cab. You’ll have the load charts, control designations, and safety procedures that Furukawa Unic engineers wrote for exactly your machine.