Description

Dynapac F2500C 2017 Parts Catalog – Factory Specs for the Tracked Paver

If you’ve ever ordered a wear kit for a paver and got the wrong width auger wings or a conveyor chain that didn’t match the pitch, you know the pain. This Dynapac F2500C 2017 Parts Catalog is the OEM document that puts the right part numbers in your hand. No chasing aftermarket cross-references that may or may not fit. This is the same 575-page book the Dynapac dealers use to pull parts off the shelf.

Wear Part Kits: What’s Included for Tier 3

The catalog breaks down every service, repair, and wear part kit by the engine stage – Stage IIIa / Tier3. You get a dedicated section for wear part and inspection kits, then sub-sections for auger, hopper, conveyor, drive, and service kits. For example, the auger kit section lists part number 4812027478 for the Wear part kit auger wings Ø380mm. That exact diameter is critical because a 380mm wing won’t fit a 400mm auger assembly. The hopper kit 4812018439 covers the standard rubber. If you need the conveyor guide plates, the kit PN is 4812225799. Each line gives you the base PN and whether it’s a single or complete assembly. I’ve seen too many guys order the wrong conveyor chain because they guessed at the link count – this catalog ends that guesswork.

Service Kits – 500h and 1000h Intervals

For the Cummins Tier3 engine, the catalog lists two service intervals. At 500 hours you have the standard Service kit 500h TIER 3 (PN 4700691229) and a Plus version (4812043983). At 1000 hours there’s a stage 2 kit (4812046969), a Plus kit (4812023851), and a separate Filter kit (4812023923). Each kit groups the filters, belts, and wear items that should be replaced at those intervals. If you’re running a fleet of F2500Cs or just keep one in the barn, having these PN groups saves you from cross-referencing aftermarket catalogs that might substitute a part that doesn’t meet OEM specs. The lubricants section on page 17 lists the approved fluids – don’t mix generic hydraulic oil unless you verify it meets the OEM spec.

Side Screed Arms: Mechanical Locking Details

One of the assemblies I paged through was the side screed arms with mechanical locking (PN 4812027554A). The catalog shows the left-hand side screed arm (4812029165) and right-hand (4812029197), plus the locking mechanism (4812029222) and side arm guiding (4720000097). If you’ve ever had a side screed arm drift during a pave, you know the locking mech has to be right. The parts list includes exploded views – I can’t show them in text, but the part number hierarchy tells you what bolts to the subframe. For the push roller with hydraulic crosshead (4812044911A), the pillow block PN is 4812046568. That’s a common wear item if the crosshead binds. Replace it with the OEM block, not a generic bushing.

Covering and Hood Components – How They’re Structured

The catalog covers every panel on the F2500C. Take the isolated covering assembly (4812004491C). It lists the bulk head (4812225668), rear air guide (4812225657), support plate (4812225681), retainers, center covers left and right, and the hood support (4812226900). If you’re replacing a damaged hood or insulation, you need the exact retainer PN – 4812226380 for left, 4812226135 for right. The intermediate section (4812226906) and air guides left (4812226902) and right (4812226899) are all broken out. The catalog even has a revision covering from serial number FG001594 (PN 4812226471C) – so if your paver was built after that SN, you need the later parts. Ignoring the SN splits is how you end up with a door that doesn’t latch.

Why an OEM Parts Catalog Beats Aftermarket Lists

Aftermarket parts catalogs often group parts by vehicle type and take shortcuts on the detailed sub‑assemblies. This Dynapac F2500C 2017 Parts Catalog is the original factory file – not a third‑party reprint. Each PN is verified against the 2017 production run. The print date on page 1 is 9th Jan 2017, and it applies to the Cummins Tier3 / Stage III engine. If you need the Dynapac F2500C 2014 Parts Catalog for an earlier model year, that’s a separate document. For other Dynapac equipment, check the Dynapac PL2000LS Parts Catalog (258 Pages) – OEM Factory Spec or the Dynapac PL2000LS Parts Catalog – Factory OEM Specs for Cold Planer. The official Dynapac website also has support bulletins, but for exact part numbers this catalog is your source. For context on why OEM documentation matters in heavy equipment, see the Automotive Industry Overview.

Bottom line: if you maintain or repair a Dynapac F2500C, having the factory parts catalog means you order the correct 500‑hour service kit, the right wear part kit auger wings, and the exact side screed arm locking mechanism. Don’t trust a parts store lookup that might give you a generic conveyor chain. Access the Factory Manual and get the actual PN list for your tracked paver.

Does this catalog include torque specs or repair procedures?

No. This is a parts catalog only. It lists part numbers and exploded assemblies. For repair instructions, you need the separate service manual.

What engine stage does this cover?

It covers the Cummins Tier3 / Stage IIIa engine. The catalog explicitly states “Tier3” in the service kit sections.

How do I know which wear kit fits my paver’s auger diameter?

The catalog lists the auger wing kit as Ø380mm (PN 4812027478). If your auger is different, you need a different kit. Check the serial number range on your paver – the catalog includes revision splits for later machines.

Can I use this catalog if my F2500C was built after 2017?

It covers up to the 2017 production year. For later SNs, Dynapac may have released a revision (like the covering from SN FG001594). This catalog includes that revision. For newer models, look for a 2018+ parts catalog.