Description

Dynapac F1000T 2015 Parts Catalog

You’ve got a Dynapac F1000T tracked paver down with a bad bearing on the auger extension. You pull up a generic parts site, punch in the model, and get three different part numbers that all claim to fit. One costs half as much. Which one do you order? If you pick wrong, you’re down another day while the correct part ships. That’s the kind of headache this 2015 Parts Catalog kills dead. This is the actual document the factory uses to order parts. Not a reprint, not a third-party compilation. 435 pages of OEM exploded views, kit breakdowns, and part number cross-references for the F1000T serial number 10002134CEC004555.

Let’s talk about what you actually get when you open this PDF. The table of contents alone lists over thirty service and wear part kits, each keyed to a specific interval or subsystem. The 100-hour startup kit, the 500-hour maintenance kit, the 1000-hour kit – they’re all here with their exact Dynapac part numbers. No guesswork. You see “4812269054 Kit, start up, 100 Hrs” and you know it’s the correct bundle of filters, seals, and gaskets for the T4i engine variant. The manual also spells out the auger extensions in left and right pairs (D722182100 and D722182200) with separate part numbers for the long and short versions. That kind of granularity matters when you’re ordering from a dealer and the counter guy says “they’re all the same.” They aren’t.

Service Kits and Maintenance Intervals

If you run a fleet or own one of these pavers, the service kit section is where you’ll start. Every interval has its own kit number. The 100-hour kit is 4812269054, the 500-hour kit is 4812269055, and the 1000-hour kit is 4812269056. These aren’t generic “tune-up” bundles. They’re spec’d by Dynapac engineering for the QSB6.7-C225 engine. The manual also includes the D717955090 Uptime kit – a package of high-wear items that keeps the machine going when you’re on a tight schedule. You’ll find the auger reinforcement kit (4812269105), conveyor bearing kit (4812269064), and the hopper skirt kits for standard and low versions. Every kit has its own exploded illustration and part number callout. You can literally hand page 9 to the parts clerk and say “I need item 12.”

Which Hydraulic Components Are Covered?

Hydraulic troubleshooting is a pain when you don’t have the right drawings. This catalog covers the pump drive assembly – splitter gear box (4812200078), the propel front and rear pumps (D717191000 and D717191500), the auger tandem pump (D717192500), and the vibration pump (D717193001). There’s also the gear pump for the fan drive (4812222519) and the generator pump (D717193500). Each pump assembly is shown with its mounting bolts, fittings, and O-rings. You get the hydraulic component section starting on page 2 of the PDF, with specific valve banks: rear work function (D717091507) with its HIC valve (D717953711), front manifold (4812200104), and the propel gearbox HIC (D717090503). The vibration valve (D717091508) is broken down with its cartridge and pilot stage. If you’ve ever fought a machine that won’t vibrate because of a misidentified solenoid, you’ll appreciate having the exact Dynapac part number in front of you.

435 Pages of Factory Part Numbers

Page count isn’t marketing fluff here. 435 pages means every nut, bolt, seal, and hose is listed. The frame assembly for the 10’ crawler paver starts on page 57, including the front conveyor cover, guide pole, adjustable scraper, and fume extractor. The platform assembly covers both left and right operator stations, side doors, footwell, cooler shroud, anti-slip tape, door assembly, foam insulation, seat lock, and hood frame. The electrical system section includes the generator drive (D717100501 34kW generator), battery box assembly (4812223611), and both left and right operator console assemblies (4812246958 and 4812246959) with the propel handle controller (D717101501) and its maintained center switch (4812270342). Every single part number in this manual came from the Dynapac factory, not from a reverse-engineered aftermarket source. When the manual says “Use only authorized parts” on page 2, it means it – and this is how you identify them.

Engine System: Engine Part and Cooling System Details

The engine system section (starting on page 73) covers the QSB6.7-C225 power plant. You get the air cleaner (4812222043), the oil drain hose, and the mounting bracket assembly. The cooling system includes the combi cooler (4812222304) and the exhaust system. The parts are shown in exploded views with the correct fastener torque specifications noted in the assembly instructions. If you’re swapping a radiator or replacing a hose, you can confirm the exact clamp size and hose routing. This is the same documentation the dealer’s service department uses to write repair orders.

Use Only OEM Part Numbers for Safety

I’ve seen what happens when someone substitutes a cheaper hydraulic filter from a supply house. The bypass pressure doesn’t match, and the charge pump cavitates. On a paver that feeds the screed plate, that means striping and downtime. This catalog gives you the factory filter assembly (4812220770 for the hydraulic filter tier IV) and the exact micron rating specified by Dynapac. The same applies to the auger charge oil filter (4812220876). If your machine has the tow point indicator, the assembly is shown with its bracket and harness. Using OEM parts isn’t about brand loyalty – it’s about matching the original engineering specs so the machine doesn’t fail at 3 PM on a Friday.

Source Validity: Why This Beats Aftermarket Catalogs

I’ve been burned by aftermarket parts lists that claim “fits F1000T” but leave out the serial number split. Dynapac changed the auger drive configuration mid-2015; this manual covers the IV/T4 variant with serial number 10002134CEC004555 and later. The aftermarket catalogs I’ve seen lump all F1000T models together, which is how you end up with the wrong extension length. This PDF is a direct copy of the 2015 publication from Dynapac (Atlas Copco group), with the original copyright and part number 4812243642. It’s not a scan of a scan. The exploded views are clear enough to read the part numbers without squinting. For more on how the construction equipment industry standardizes documentation, check the Automotive Industry Overview.

If you need related documentation, the Dynapac PL2000LS Parts Catalog (258 Pages) – OEM Factory Spec covers the cold planer line, and the Dynapac PL2000LS Parts Catalog – Factory OEM Specs for Cold Planer gives you the same level of detail for a different machine. The Dynapac F1000T 2015 Parts Catalog – Factory OEM Specs is the exact manual you’re looking at now.

Does this catalog include torque specifications for assembly?

No. This is a parts catalog, not a service manual. It lists part numbers and exploded views. Torque specs are in the separate service manual. Get both.

I see the serial number 10002134CEC004555 listed. Will this work for an older F1000T with a different serial?

Dynapac split the parts by serial number range. This edition covers the IV/T4 engine tier from that serial forward. If your machine is an earlier serial, some components (like the auger extensions and hydraulic valve banks) may differ. You can verify by comparing the part numbers in the auger extension section – the left extension D722182100 and right D722182200 are specific to this series. For an older machine, you would need the corresponding earlier parts catalog. The warranty statement on page 2 explicitly says damage from unauthorized parts is not covered, so using the correct catalog for your serial is critical.

Stop wasting time chasing wrong part numbers. Access the Factory Manual and get the exact OEM part numbers for your Dynapac F1000T. You’ll have the right kit on order before the next break.