Description

Dynapac CC142 Parts Catalog

If you are maintaining a Dynapac CC142 Parts Catalog vibratory tandem roller and you have ever ordered the wrong bearing or seal because you guessed the part number, this is for you. I have seen guys burn a whole afternoon chasing a part that doesn’t match because they grabbed a number off a generic website. The factory catalog kills that headache cold. 288 pages of exploded-view diagrams, factory part numbers, and the exact ordering procedure you need to get the right piece the first time. This is the same document the Dynapac dealer uses. Nothing else.

Ordering Spare Parts: What the Factory Requires

Page 4 spells out the six things you must give when you call in an order. Machine type. Roller serial number. Quantity. Part number. Parts denomination. Dimensions for anything sold by length. Skip any of those and you get the wrong box. The catalog includes the serial number range for your CC142 so you can verify which edition applies. Look at the top of page 1 for the model identifier and the serial number block. Do not assume your roller is covered just because it says “CC142” on the side. There are seven catalogue revisions from SCC142-2EN1 to SCC142-2EN8, each superseding the previous one. This edition (SCC142-2EN8) covers rollers from serial number 60212800 onwards. Check yours.

288 Pages of Exploded-View Diagrams

Every chapter breaks the roller down into assemblies – frame, drum, engine mount, steering, hydraulic system, electrical. You get a clean exploded view with each part called out by number. Underneath that is a table listing the part number, description, and quantity. No vague references. No “see similar”. The DYNAPAC CC142 2011 Parts Catalog covers the same layout if you need an older revision. For this one, the diagrams are sharp enough to read on a tablet while you are standing next to the machine. The paper version is better for the bench, but the PDF lets you zoom in on the small stuff.

Diesel Engine Coverage: DEUTZ F3L 2011 and D2011 L03 I

Two engine options are listed in this catalog. The DEUTZ F3L 2011 and the DEUTZ D2011 L03 I. Each has its own section with separate part numbers for injectors, gaskets, filters, and cooling components. Do not try to swap parts between them without checking the diagram. The part numbers are different for a reason. Page 4 of the ordering instructions also reminds you to give the engine serial number if applicable. That is not a suggestion. I have had to reorder a cylinder head gasket because someone read the wrong line. Read the line that matches your engine family.

Why a Factory Parts Catalog Beats Aftermarket Lists

Aftermarket databases compile part numbers from multiple sources and often merge updates incorrectly. This catalog comes directly from Dynapac (Atlas Copco group). Every number has been verified against the production line. If the OEM changed a seal supplier mid-year, the catalog shows the supersession. Try getting that from a third-party site. You cannot. The Dynapac CC142 Spare Parts Catalog on this site is the same file the factory ships to dealers. No editorial changes. No guesswork. That matters when you are ordering a $400 hydraulic pump and you need it to fit.

CC142 Serial Number Validation and Revision History

Before you dig into the diagrams, confirm your machine’s serial number against the list on page 3. The table shows each catalogue issue date and the serial numbers it covers. For example, SCC142-2EN1 started in 2004-01, SCC142-2EN2 replaced it in 2005-03, and so on up to this one (2009-12). If your roller is older than 2004, you need an earlier revision. The Dynapac CC142C Spare Parts Catalogue might be the right one for certain variants – check the model plate. Do not skip this step. You will waste money.

Tools and Safety – What the Catalog Expects

This is a parts catalog, not a service manual, so it does not list torque values or repair procedures. But anyone ordering parts for a vibratory roller knows that safety comes from correct fit. A wrong bolt in the vibratory mount can shake loose and cause damage. The exploded views show you exactly which bolt grade and length goes where. Use the part number to order the factory bolt. Do not substitute with hardware-store stock unless you cross-reference the grade. For general automotive repair safety context, you can reference the Automotive Industry Overview for common tool standards, but stick to OEM parts for the roller.

Does this parts catalog include repair procedures?

No. It is a parts catalog – exploded diagrams and part numbers only. For service steps, you need the Dynapac CC142 service manual sold separately.

How do I know which part number is for my roller’s serial number?

Look at the serial number range table inside the front cover. Locate your roller’s serial number (stamped on the frame plate) and match it to the applicable catalogue issue. Then find the assembly diagram for that system. Each part number in the table corresponds to a callout on the diagram. If your serial number falls outside the range listed on page 3, you need an earlier revision of the catalog. We stock those as well – check the related manuals below.

Stop ordering parts by guesswork. Access the Factory Manual for your Dynapac CC142 and get the exact part numbers you need. 288 pages, OEM-sourced, ready to use.