Description

Combilift AMEL001, AMEM201.1 2016 Parts Catalog — Factory OEM Breakdown

If you’ve ever ordered a fastener for a Combilift forklift and ended up with a bolt that’s half a thread pitch off, you know the pain. Third‑party part cross‑reference sheets are a gamble. This is the factory Parts Catalog — printed 2016, 68 pages thick, and packed with revision dates like 26/05/2016 on the Front Chassis Assembly. It’s what the guy on the assembly line used. No guesswork.

Front Chassis Assembly – Page 1 Breakdown

Open to page 1 and you see the Front Chassis Assembly drawing for the Combilift AMEL001. Every numbered callout ties to a parts table that lists the description, part number, and revision level. The steering column assembly is flagged “See Section 8” — no lazy reprint of the same diagram. The low nose bearing clamp (part 26A00245, Rev 11‑A) is specified alongside the correct bolt: M16x45 socket head bolt, CPB00309, Rev 01‑A. Those Class 12.9 bolts on items 28? They’re not optional. If you replace them with a Grade 8, you’re asking for a shear failure.

Mid Chassis Assembly – Key Fastener Specs

Page 2 of the manual covers the Mid Chassis Assembly for the AMEM201.1. The brake pedal gets its own section reference, but the real meat is the fastener schedule. Combilift calls out M12x75 socket head bolts (Class 12.9, part CPB00525) for the accelerator pedal bracket. The hand brake micro switch (22E50055) has its own Rev letter. If you’re replacing that switch and the catalog says “Machine Serial Number Must Be Quoted When Ordering Items Marked With *”, ignore that at your own cost. The wrong micro switch won’t throw the same alarm circuit.

Why a Factory Parts Catalog Beats Aftermarket Lists

I’ve seen aftermarket “universal” parts guides list a single M8x20 bolt for an entire chassis. This manual gives you dome head bolts, socket head bolts, hex head bolts, and flat washers — each with its own part number and revision. The M8 dome head bolt on item 21 (part CPB00183) is not the same as the M8 socket head bolt on item 27 (CPB00565). Aftermarket catalogs don’t make that distinction. This one does, because it’s straight from Combilift’s engineering department. The Automotive Industry Overview teaches that original equipment data is the only reliable source for torque and fastener grades.

Audience Fit – Who Needs This Manual

If you’re a fleet manager ordering replacement parts for a dozen Combilift units, this catalog saves you from having to measure every bolt. A home‑garage guy who inherited an old AMEL001? You’ll use this to track down that 100mm bearing (GE100 ES2RS, part 22B50003) without guessing the SKF equivalent. And if you’re a technician who bills by the hour, having the exact part number on page 1 for the mast carrier slew ring (VA160235N, 22B50002) means you order it once, not twice. The Combilift C4000 Electrical Schematic – 23-Page OEM Wiring Manual would pair well with this parts catalog if you’re chasing an electrical issue.

3 Rules for Ordering Parts from This Catalog

First, always check the revision date on the section header. The Front Chassis sheet is Rev 01‑A dated 26/05/2016 — that matters because a later revision might supersede a part number. Second, if the parts table says “Serial Break” (you’ll see those columns), stop and read the note. Some items changed after a specific serial number. Third, never ignore the washer specs. Item 14 calls for “12 M12 Flat Washer” – CPB00082, Rev 02‑A. That’s a specific thickness. A generic washer from the bin may not crush the same way. Internal Combustion Engine fundamentals apply here — fasteners distribute load, and factory catalogs capture that.

This isn’t a repair manual. It’s a parts ID book. But if you’ve got a Combilift AMEL001 or AMEM201.1 on the lift and you’re staring at a broken steering orbital, the answer is in these 68 pages. The Combilift AMEL001 / AMEM201.1 Parts Catalog 2016 is the one you want on the bench, not a photocopied chart from the internet.

Does this Parts Catalog include torque values?

No. This is a parts identification manual, not a service manual. Torque specs appear in the corresponding workshop manual. The catalog focuses on part numbers, descriptions, and revision history.

How do I tell which revision applies to my forklift?

Check the serial number on your machine’s plate. The catalog includes “Serial Break” columns in the parts table. If your serial number falls within a break range, use the newer revision part. For example, the Front Chassis Assembly Rev 01‑A applies to early builds; later serials may require a different steering orbital.

Where do I find the part number for the brake pedal assembly?

Page 2 of the catalog shows the Mid Chassis Assembly. Item 1 is the brake pedal assembly, but it references “See Section 13” rather than listing a direct part number. That section is not in this catalog — you’ll need the full service manual or a separate brake assembly drawing.

Are the bolt grades listed in the parts table?

Yes. Many fasteners include the grade in the description, e.g., “M12x110mm Hex Head Bolt (Class 10.9)” or “M16x60 Socket Head Bolt (Class 12.9)”. Aftermarket catalogs often omit this.

You can Massey-Harris-Ferguson FF 30 GS 1957 Parts Catalog | OEM Fastener Guide if you’re working on older equipment, but for a modern Combilift, stick with the factory data. Access the Factory Manual and put the correct part number on your order form.