Description

SAME Deutz-fahr Agrotrac 110, Agrotrac 130, Agrotrac 150 Workshop Manual

You’ve got an Agrotrac 110 in the bay with a clutch pedal that feels like stepping on a sponge. You reach for a manual, find some aftermarket PDF that shows a generic tractor clutch diagram and says ‘adjust as necessary.’ That’s how you waste half a day and still get it wrong. This SAME Deutz-fahr Agrotrac 110, Agrotrac 130, Agrotrac 150 Workshop Manual is the actual book the dealer techs used. 437 pages of procedures, torque specs, and inspection checks for the Agrotrac 110, Agrotrac 130, and Agrotrac 150. Every step is written for a trained mechanic who doesn’t have time to guess. The original file name alone tells you it came from Deutz-Fahr itself – not a reprint, not a third-party compilation.

Gearbox Clutch: Dismantling and Reassembly (Pages 1–18)

The clutch section covers the pedal assembly, master cylinder, slave cylinder, hydraulic lines, and the clutch itself. You get the full sequence: DEPOSE (removal), VERIFICATIONS ET CONTROLES (checks and inspections), REGLAGES (adjustments), and REPOSE (reinstallation). Page numbers for each subassembly are given so you can jump straight to the job. The manual even lists the special tooling required (page 16). This is not a generic clutch service guide – it’s specific to the Agrotrac series. When you pull the clutch, you need the flywheel runout spec and the pressure plate bolt torque. That data is in the technical data section on page 15. No flipping through a separate supplement.

7 Major Systems Covered from Engine to Piping

Look at the table of contents: ENGINE (Section VII), GEARBOX CLUTCH (1–18), GEARBOX (19–112), GEARBOX LUBRICATION SYSTEM (113–120), CLUTCH P.T.O (121–140), FRONT AXLE (141–160), FRONT DRIVING AXLE (161–198), BACK AXLE (199–212), BRAKES (213–242), WHEELS AND TYRES (243–246), HYDROSTATIC STEERING (247–268), PIPING (269–270). That’s seven system groups covering every major component on the tractor. Each section includes dismantling, inspection, reassembly, and technical data. The gearbox section alone runs nearly 100 pages because it covers the standard gearbox, the version with mini-reducer and reverser, and the super-reducer variant. You get the shaft layouts, synchro inspections, and bearing clearance specs. For the Manual Transmission, this is the level of detail you need to rebuild it correctly.

Does This Manual Include Torque Specifications?

Yes, but not in a standalone table. The technical data section on page 15 lists tightening torques for the clutch, gearbox, and axle components within each procedure. For example, when you reassemble the clutch, the manual tells you the torque for the pressure plate bolts and the flywheel bolts. The same goes for the gearbox bearing retaining nuts and the axle hub bolts. This factory data is specific to the Agrotrac 110, 130, and 150 – not a generic range. If you rely on an aftermarket manual, you get ballpark numbers. Here, you get the exact values SAME Deutz-fahr stamped into their production line.

Get the Right Gearbox Lubrication Data

Page 113 starts the lubrication section for the gearbox. It covers oil capacities, grade specifications, and the routing of lubrication lines. If you’re swapping a gearbox or just doing a fluid change, you need the correct fill volume and the recommended oil type. The manual also includes a troubleshooting chart (page 17) that lists common gearbox noises, shifting issues, and the probable causes. Don’t waste time chasing a synchro problem when it’s just low fluid – check the chart first. And if you’re deeper into the transmission, the Manual Transmission section gives you the shaft assembly sequence with the exact shim thicknesses and preload values.

Factory OEM Print vs Aftermarket Copies

Every page of this manual is a scan of the original Deutz-Fahr publication. The OCR excerpt shows the introduction written for trained technicians who attend the SAME Deutz-fahr Service School. The instructions are dense and assume you know how to use a torque wrench and a dial indicator. Aftermarket manuals condense the information, skip the inspection steps, and sometimes change the torque values to fit a generic tractor. This manual gives you the full 437 pages – no editing, no paraphrasing. If you’re rebuilding a back axle (pages 199–212) or bleeding the hydrostatic steering (page 247), you get the OEM procedure, not a summary. The piping section (page 269) shows the exact routing of hydraulic hoses for the clutch and steering circuits. That matters when you’re replacing a line and need to avoid a kink.

Related Manuals

• SAME Deutz-fahr 110, 130 Workshop Manual – OEM Factory Specs
• SAME Deutz-fahr 80, 105 Workshop Manual – Hydraulic Inversor Specs
• SAME Deutz-fahr 1000 Workshop Manual – Factory OEM Engine Specs

Frequently Asked Questions

Is this manual in English?

Yes, the manual is in English.

What torque values are provided?

The manual contains technical data and prescriptions on page 15, including tightening torques for major components like the clutch assembly, gearbox shafts, and axle fasteners. It also lists fluid capacities and lubrication specifications. You won’t find a separate torque specification table unless you look at the specific sections – each procedure includes the required torque at the step. This is factory data, not aftermarket approximations. The clutch flywheel bolts, for instance, get the exact ft-lb value from the OEM. No more hunting across forums.

437 pages. No aftermarket guesses. If you work on these tractors, you need the actual workshop manual from SAME Deutz-fahr. Access the Factory Manual now and get back to turning wrenches with real specs.