Description

Massey Ferguson 7254, 7256 Parts Catalog

I’ve seen too many guys order a bolt from memory and end up with a grain tank sitting on the shop floor because the thread pitch was wrong. This is the Massey Ferguson 7254, 7256 Parts Catalog — 487 pages of factory part numbers, not a third-party reprint. Every bolt, every seal, every decal is listed with the exact OEM number. If you’re working on a 7254 or 7256 combine, you use this book or you’re fishing.

Engine and Hydraulic Groups: Factory Part Numbers

Group 8 (ENGINE) and Group 14 (HYDRAULIC) cover the heart of the machine. The engine section lists every component from the block to the injection pump — including the specific hardware you need for the mounting brackets. Hydraulic section gives you the pump, valves, and cylinder part numbers. A lot of aftermarket catalogs skip the hydraulic fittings. This one doesn’t.

Does This Catalog Cover the Threshing Drum and Straw Chopper?

Yes. Groups 4 (CONCAVE, THRESHING DRUM AND REAR BEATER) and 17 (STRAW CHOPPER) are in here. If you need the concave assembly or the chopper knife set, the exploded view on the illustration page shows each part with its reference number. Column E in the part reference list tells you if a part is part of a kit. Don’t guess.

18 Major Assembly Groups and 487 Pages

The catalog indexes 18 groups — from the TABLE (Group 1) to DECALS (Group 18). That’s 487 pages of part numbers, illustrations, and cross-references. The RECOMMENDED STOCKING PARTS section at the front gives you a list of high-wear items you should keep on the shelf. If you’re a dealer or a farm shop, that section alone pays for the book.

Cross-Reference Parts with the Numerical Index

Three indexes are built in: ALPHABETICAL, NUMERICAL, and GROUP INDEX ALPHA. If you have a part number from an old invoice, the NUMERICAL INDEX (page 3 of the contents) gets you to the illustration. The GROUP INDEX ALPHA lets you hunt by assembly name — English, French, or German. The manual is multi-language, so if you’re dealing with a machine that came from Canada, you’ll find the terms in French too.

RECOMMENDED STOCKING PARTS: Why You Need This List

Page 1 of the table of contents points to the RECOMMENDED STOCKING PARTS section. These are parts that Massey Ferguson identified as common failure or high-turnover items. Each part shows a quantity used per figure. If you see an asterisk in Column B, that means there’s been a change since the last print. Massey Ferguson 7254, 7256, 7200 SERIES Technical Manual – OEM Specs gives the torque specs and repair procedures that this parts catalog doesn’t cover. You need both books to do the job right.

The part number format is straightforward: 10-digit codes starting with D. D6116894 is a recommended stocking part. D55789492 is a marketing key part. The catalog’s explanation on page 4 shows how to read the columns. If a part has an ‘X’ in the quantity column, it means quantity as required — like shims or washers. Don’t order one if you need ten.

I’ve used aftermarket parts lists that show a generic bolt where the factory called for a specific grade. That’s how you snap a header support on a full hopper. This catalog gives you the exact OEM number so you can cross-check it with Massey-ferguson MF300 Parts Catalog – 607 Pages – Factory OEM or Massey-Ferguson MF500 1977 Parts Catalog – 517 Pages Factory OEM if you’re mixing model families. But stick with the factory book for the 7254/7256. Automotive Industry Overview standards are fine for reference, but your combine isn’t a car. Agricultural parts catalogs follow a different convention. Automotive Industry Overview won’t tell you the thread pitch for a Massey Ferguson clevis bolt.

Can I use this catalog to order parts for a 7256?

Yes. The catalog covers both 7254 and 7256 models.

What is the difference between a Parts Catalog and a Service Manual?

A parts catalog like this one gives you exploded views, part numbers, and ordering information. It does not include repair procedures, torque specs, or diagnostic steps. For that you need the factory service manual — the technical manual we also carry for the 7254/7256 series. A parts catalog tells you what to buy; a service manual tells you how to install it. If you’re rebuilding the engine, you absolutely need the service manual to get the bearing clearances and bolt torque values. The parts catalog alone will leave you with a pile of new parts and no instruction on how they go together.

Does the catalog include torque specs?

No. This is a parts catalog, not a service manual. It lists part numbers and quantities. For torque values, you need the factory technical manual for the 7254/7256. Some parts lists will note a “kit” or “set” — but torque values are not part of this document.

How do I read the part number reference list?

Page 4 explains the table. Column A is the illustration reference number. Column B shows an asterisk if the part changed since last print. Column C is the part number. Column D indicates if the part is also a component of an assembly, with the assembly illustration number. Column E has comments (symbols, notes). Column F is quantity — an ‘X’ means quantity as required. Columns G, H, J give the description in English, French, and German. Use the NUMERICAL INDEX to find the part number page if you already have a number.

This catalog is an original factory print — not a scan of a scan. The issue number and date are printed on each illustrated page. If you’re rebuilding a Massey Ferguson 7254 or 7256, this is the only parts list you should trust. Access the Factory Manual from AutoRepairManuals and keep a copy in your shop tablet. You’ll save yourself a trip to the dealer counter.