Description

John Deere 700J 2007 Parts Catalog

You are tearing down a 700J undercarriage and you need a track roller – the aftermarket cross-reference says it fits, but the bolt pattern is off by half an inch. That cost you an afternoon and a restocking fee. That is why you do not guess with undercarriage parts. This John Deere 700J 2007 Parts Catalog is the only way to get the right part number the first time. 439 pages, factory-original, no reprints.

What This Parts Catalog Actually Covers

This is not a service manual. It is a parts identification catalog – exploded diagrams and part numbers for every bolt, seal, roller, sprocket, and guard on the 700J. The table of contents breaks it down by major assemblies: TRACK FRAMES AND UNDERCARRIAGE (section 0131), CHAINS AND SHOES, DRIVE SPROCKETS (0132), ROLLERS, IDLERS AND IDLER SPRINGS (0133), DRIVE AXLE HOUSING AND SUPPORT (0201), TRANSMISSION CONTROLS (0315), INPUT DRIVE SHAFTS AND U-JOINTS (0325), and VARIABLE SPEED DRIVES (0355). Each section has detailed sub-sections – for example, under 0133 you get TRACK ROLLERS AND COMPONENT PARTS (page references within the PDF) and CARRIER ROLLER WITH COMPONENT PARTS.

Get the Right Part Number Before You Order

Page 4 of this catalog shows you exactly where to find the seven serial numbers on the machine – Product Identification Number, engine, hydrostatic motors, pumps, and micro-computer. The manual tells you that the PIN is on the left-hand side of the frame below the operator station, and the engine serial is on the right side of the block. Without these numbers, you are ordering blind. This catalog is indexed by serial number range (S.N. 139436-), so you need to verify your machine matches before you buy a single part.

439 Pages of Factory-Correct Diagrams

At 439 pages, this catalog covers every system. The TRACKS section alone runs over 50 pages with separate sheets for LT, LGP, and XLT rockguards, rear rockguards, rock deflectors, and final drive guard kits. Each diagram has a part number callout and a corresponding list. For the transmission, you get exploded views of the flywheel coupler, tandem pump components, and the hydrostatic pump charging system manifold. If you are rebuilding a final drive or replacing a drive sprocket guard, you find the exact fastener lengths and seal IDs.

Using Serial Numbers: Key to Accurate Parts

This catalog was published April 2007 for Tier 3 machines. The introduction on page 3 states: “Part numbers were correct at time of publication.” That means if your 700J is a later production run or has been modified, you cross-check with your dealer. The serial number location guide on page 4 helps you identify every component – including the micro-computer serial number on the bottom of the unit. Never order a hydrostatic pump without first locating the pump serial number on the housing.

Related Manuals for Full Service Coverage

This parts catalog works best alongside the technical manual. You can pair it with John Deere 700J 2012 Technical Manual – 376 Page Factory Specs for torque values and repair procedures. For earlier models, see John Deere 2130 Parts Catalog – Factory Specs for Correct Part Identification. For more context on the engine used in this platform, reference this Wikipedia article on diesel engines.

Frequently Asked Questions

Does this catalog include torque specs for bolts?

No. This is strictly a parts identification catalog. It shows you the part number and quantity – not how tight to turn it. For torque values, you need the technical manual.

Will this catalog work for a 700J with serial number 139435?

This edition covers S.N. 139436 and up. If your machine is older, you need the pre-Tier 3 catalog. Check the serial number plate on the left frame rail.

Can I use aftermarket parts catalogs instead of OEM?

I have had aftermarket catalogs show the wrong thread pitch on final drive bolts. When you are ordering parts for a $200,000 crawler, do not trust a third-party reprint. OEM is the only way to guarantee fitment.

How do I find the part number for a carrier roller?

Go to section 0133 in the catalog. Look under “CARRIER ROLLER WITH COMPONENT PARTS.” Find the diagram, note the item number, then read the part number from the list. That number will get you the correct roller assembly.

If you are ordering parts for a 700J and you want to avoid the headache of returns and downtime, this is the document you keep on the bench. 439 pages of factory drawings, every part number verified by John Deere. Access the Factory Manual now from AutoRepairManuals – John Deere 700J 2007 Parts Catalog is available in printable PDF format.