Description

Hyster P1.6, P1.8, P2.0 2006 Parts Catalog

If you’re hunting for a part on a Hyster P1.6, P1.8, or P2.0 and you pull out a generic aftermarket listing, you’re wasting time and risking a wrecked piece of equipment. I’ve seen guys bolt on the wrong load wheel because the online cross-reference said “fits all” – then the truck sits dead while you hunt for the real part number. This is the 2006 factory parts catalog, straight from Hyster. 54 pages, no guesswork. Every sheet index is in here: covers, frame, traction unit, hydraulic system, electrical diagrams. You need a part, you look it up by serial number and sheet number. Done.

54 Pages of Factory Specs – No Substitute

This catalog runs 54 pages, covering the P1.6, P1.8, and P2.0 with multiple language sections – English, Italian, French, German, Spanish. That means you don’t have to translate foreign part numbers. The part sheet index starts on page 2 and lists every group: COVERS (Sheet 1.A, pages 6-7), ADHESIVE LABELS (Sheet 2.A, pages 8-11), FRAME BATTERY VERTICAL REMOVAL (Sheet 3.A-3.B, pages 12-13), SUPPORTS AND CASTER WHEELS (Sheet 4.A, pages 14-15), LOAD WHEELS (Sheet 5.A, pages 16-17), and the big one – TRACTION UNIT (Sheet 6.A, pages 22-27). Each sheet has an exploded view with callouts and the exact Hyster part number. No cross-shopping a parts diagram from some third-party site that swapped a digit. This is the real deal.

Traction Unit Parts: Sheet 6.A Breakdown

Your drive motor is the heart of the pallet jack. The catalog separates traction motors: Sheet 7.A for P1.6/P1.8, Sheet 8.A for P2.0. The magnetic brake (Sheet 9.A) is a separate assembly. Page 22-27 of the traction unit group show the gearbox, drive wheel, and mounting hardware. If you’re swapping a motor or gearbox, don’t slap on a reused seal – the catalog lists the part number for the correct O-ring. And while you’re at it, check the caster wheels (Sheet 4.A) – they’re on pages 14-15. Replace both sides, not one, unless you want the truck pulling left. That’s not a guess – that’s experience.

Need the Battery Charger Part Number?

Two sheets cover the charger: Sheet 13.A for P1.6 (pages 35-38), Sheet 14.A for P1.8/P2.0. If you have a cold-store variant, the wiring diagrams (Sheet 15.A for P1.6 STD & cold store, Sheet 16.A for P1.8 STD & cold store / P2.0 STD, and Sheet 16/1.A for P2.0 cold store) show the differences. The charger connector pin-out is different between standard and cold-store – get it wrong and the contactor won’t pull in. The factory schematic tells you which wire goes where. Aftermarket scans often blur the pin numbers. Not this one.

Match the Part Number to Your Serial Number

Page 2 of the catalog tells you exactly what information to provide when ordering: truck model, serial number, table number, part number, quantity, description. The serial number range starts at C437X01501A. If your truck is before that, you need the earlier catalog. This one covers from that serial number onward. And note the exception lines: “With the exception of” and “Including” columns – some parts vary by production run. Don’t skip that step. I’ve had guys order a complete traction unit only to find it’s the wrong spline count because they ignored the serial break. 20 minutes of reading saves 2 days of return shipping.

Electrical Diagrams: Factory Wiring vs Aftermarket Scans

The wiring diagrams are on Sheets 15.A, 16.A, and 16/1.A. They show the power cable connections (WIRING DIAGRAMS sheet) and the control schematics. The charger and controller interfaces are model-specific. For instance, the P2.0 cold store diagram is separate from the standard. Aftermarket diagrams often combine them into one sloppy line drawing, leaving you to guess which fuse goes where. Not here. Each trace is labeled with the factory wire color code and gauge. Use the wrong gauge on the hydraulic pump circuit and you’ll melt the harness. The catalog doesn’t fix that – but the correct part number for the harness does. And the diagram shows you exactly which connector goes to which solenoid.

For larger Hyster models check the Hyster H70XM H120XM 2005 Parts Catalog – 580 Pages OEM Factory and the Hyster HR45-25, HR45H, -31, -36L, -40LS 2005 Parts Catalog OEM or the Hyster H14.00-18.00XM-12, -12EC 2006 Parts Catalog – 844 Pages OEM Factory Specs. These cover bigger equipment but follow the same Hyster sheet index logic.

This catalog is part of the broader Automotive Industry Overview supply chain, and the Automotive Industry Overview resource explains why factory documentation matters for safety and liability.

Is this a repair manual or a parts catalog?

Parts catalog. For service procedures, get the factory service manual.

How do I know if a part fits my specific P2.0 serial number?

Start by checking the serial number range printed on page 2 – this manual covers from C437X01501A onward. Then go to the appropriate sheet for your model: for the P2.0 traction motor, use Sheet 8.A; for the battery charger (P2.0), Sheet 14.A. Each sheet lists the part numbers applicable to that serial range. The “With the exception of” column tells you which parts were superseded. If your truck is a cold-store variant, you need the wiring diagram on Sheet 16/1.A. Write down the sheet number, part number, quantity, and description before you call the parts counter. That prevents mix-ups with similar-looking hardware, like the load wheel hub bolts – wrong thread pitch there will strip the axle.

You want to fix that Hyster pallet jack the right way? Get the parts catalog that the factory built. Access the Factory Manual now.