Description

Genie S-60, S-65 Operators Manual – Factory Safety & Operation Specs

Look, I’ve seen guys hop into a Genie S-60 without cracking the manual. Then they wonder why the boom doesn’t respond or they put the machine on its side. This Genie S-60, S-65 Operators Manual is the factory document that tells you exactly what each control does, what the safety rules are, and how to inspect the machine before every shift. 31 pages of OEM data – no aftermarket guesswork.

Safety Rules and Operating Instructions

Page 1 opens with a warning that failure to obey will result in death or serious injury. That’s not hyperbole. This manual covers five principles: avoid hazardous situations, perform pre-operation inspection, function tests, inspect work place, and use machine as intended. You need to read and understand these before turning the key. Genie S-60 S-65 Series 2017 Parts Catalog will help when you need replacement parts, but start here.

Read the Controls Before You Touch a Lever

Controls section starts on page 7. The Genie S-60 and S-65 have specific joystick functions, platform controls, and ground controls. The manual shows each switch and its function. If you skip this, you risk unexpected machine movement. I’ve seen it happen.

31 Pages Covering Every Operating Phase

From pre-operation inspection (page 10) to maintenance (page 12) to function tests (page 16) and work place inspection (page 21). Then operating instructions (page 22), transport (page 25), decals (page 26), and specifications (page 28). Each section is a chapter in the factory procedure. Don’t skip any.

Does This Manual Cover Transport and Decals?

Yes. Transport section tells you how to secure the machine for trucking – tie-down points, weight distribution. Decals section shows every label on the machine and its location. If a decal is missing, you can order the correct one using the part numbers listed. The spec sheet on page 28 gives dimensions, weights, and fluid capacities. Need the charge pressure? Page 28. Genie S-60 S-65 Series 2012 Parts Catalog and Genie S-60 S-65 2012 Parts Catalog are related parts catalogs for ordering components.

Pre-operation Inspection: The Checklist That Saves Lives

Page 10 lists a step-by-step walk-around. Check hydraulic oil level, tire condition, boom pivot pins, emergency stop function. The manual tells you to do this every day. If you’re using a rental S-60 or S-65, you should still run through this checklist. It’s not optional.

This is an OEM manual printed by Genie, not a reprint or aftermarket compilation. The part number 43648 matches the original factory document. Aftermarket manuals often skip critical details like the specific decal part numbers or the correct hydraulic fluid viscosity. Don’t trust them. For those who also work on vehicles with a manual transmission, see our other OEM manuals Manual Transmission and Manual Transmission. But this Genie manual is strictly for aerial work platforms.

FAQ

Is this the same as a service manual?

No. This is an operator’s manual. It covers safe operation, controls, pre-operation inspection, and basic maintenance. For repair procedures, you need the service manual. This one is 31 pages, focused on daily use.

Can I use this manual for training new operators?

Yes. The safety rules and function tests sections are written clearly. I’ve used the pre-op inspection checklist from page 10 to train apprentices. It lays out every point to check. Have them read it, then walk the machine with a checklist. That way they see the machine matches the manual.

Does it include wiring diagrams?

No wiring diagrams. This is an operator’s manual. The specifications chapter gives fluid capacities and weights, but electrical schematics are in the service manual. If you need wiring, get the Genie S-60 S-65 service manual.

What about the S-65? Is it covered?

Yes. Both models are covered in this single manual.

If you’re operating or supervising a Genie S-60 or S-65, you need the factory procedures. Don’t rely on a laminated card or a verbal handoff. Access the Factory Manual from AutoRepairManuals and keep a copy in the machine’s manual compartment. It’s 31 pages of what Genie wants you to know.