Description

GEHL RS5-34 2005 Operators Manual

You’ve got a GEHL RS5-34 2005 Operators Manual waiting on the bench, and a machine that’s throwing codes or leaking hydraulic fluid. The generic manual you found online tells you to “check the lines” – useless. What you need is the factory document GEHL shipped with every RS5-34 starting at serial number 12101. That’s this manual: 86 pages of OEM data, reprinted from the original 2005 print run, form number 913227. Not a scan of a scan. Not a third-party rewrite. The schematics, torque values, and load charts are exactly what the factory put out.

Hydraulic and Electrical Schematics – Pages 70 and 74

The manual splits the hydraulic system into two schematics: one without PWP (Pressure Water Pump?) and one with PWP. Page 70 covers the standard hydraulic circuit. Page 74 lays out the full electrical schematic – every wire, switch, and indicator symbol from the dash. If you’re chasing an intermittent fault in the starter circuit or the work lights, trace it here. The electrical schematic matches the operator controls: hazard flasher, frame level, crab steer, outrigger up/down. Don’t rely on a wire color guess from a forum. Use the factory drawing.

Torque Specifications – Page 78

Standard hardware torque data on page 78. These are GEHL’s own values for the RS5-34. Wheel lug nuts, hydraulic fitting banjo bolts, frame bolts – all listed. Using aftermarket torque charts for a telescopic handler is asking for stripped threads or a joint that loosens under load. I’ve seen a wheel come off because someone used a generic table. Get the factory number and click your torque wrench to it. No guessing.

Load Zone Charts – Page 76

Load zone charts tell you the rated capacity at different boom angles and extensions. The RS5-34 is a telescopic handler – if you extend the boom without consulting these charts, you risk tipping the machine or overloading the hydraulics. Page 76 gives you the safe envelope. The manual also covers the indicator symbols for “Raise Load” and “Lower Load” on the dash. That’s not something you memorize; it’s something you reference every time you swap attachments.

Chapter 4 SAFETY – Eight Pages You Read First

Safety starts on page 8. This section runs eight pages covering hazard symbols, parking brake procedure, outrigger operation, and the shutdown override. The manual includes symbols for brake failure, engine fault, diesel fuel, and starting aid injection. If you’re a shop owner putting a new technician on this machine, make them read it. The “Shutdown Override” function alone can save an engine if the oil pressure drops. Page 3 lists international symbols you see on the dash – volume half/full, transmission temperature, crab steer. Know them before you start the engine.

Who Needs This Manual? Not Just Operators

This is an Operators Manual, but a technician working on the RS5-34 will use it for daily checks, lubrication intervals (Chapter 7), and service procedures (Chapter 8). Chapter 6 covers operation and adjustments – clutch engagement, 2-wheel vs 4-wheel steer, frame leveling. The chapter on decal locations (Chapter 9) helps you verify that warning stickers are in place. The index at the back (pages 79-86) is organized A–F, G–S, S–W, so you can find “Hydraulic Oil” or “Engine Coolant Temperature” fast. If you’re a DIY owner, you need this to perform your own service without guessing which grease fitting takes what.

Source Authenticity – OEM vs Aftermarket

This manual is not a copy. It is the original GEHL factory Operators Manual, printed in the USA in 2005. The inside cover has the form number 913527 (AP0505). I have seen aftermarket manuals that mislabel the electrical schematic or omit the PWP variant. That’s dangerous when you’re troubleshooting a no-start. This manual gives you the hydraulic schematic with and without PWP, the load zone charts, and the standard hardware torque data. It’s the document GEHL intended for the RS5-34. Related manuals: GEHL RS5-34 2008 Parts Catalog for part numbers, GEHL RS5-34, RS6-34 Service Manual – 292 Pages for deeper repair procedures, and GEHL RS10-44 2009 Operators Manual – Factory Specs & Procedures if you work on the larger models.

Torque to spec.

Frequently Asked Questions

Does this manual include repair procedures like engine overhaul?

No, this is an Operators Manual. For service and repair, see the GEHL RS5-34, RS6-34 Service Manual – 292 Pages.

I have an RS5-34 with serial number below 12101. Will this work?

The manual explicitly starts coverage at serial number 12101. If your machine is older, some procedures and schematics may differ. GEHL made design changes. You’d be better off finding a manual matching your serial range. For parts breakdowns, the GEHL RS5-34 2008 Parts Catalog covers components with part numbers. For understanding how a Manual Transmission works, the Wikipedia article is a solid resource. The RS5-34 uses a Manual Transmission – the operator’s manual covers shift patterns and clutch engagement.

Access the Factory Manual and keep it on the bench or in the cab. When the load zone chart or torque spec is the difference between a safe job and a call to the insurance company, you’ll be glad you have the OEM document.