Description

Ferri TR, TRM, 13, 22, 18 Technical Manual

If you’re wrenching on a Ferri cutter bar and you don’t have the factory documentation, you’re flying blind. I’ve watched guys guess hydraulic settings on a Ferri TR, TRM, 13, 22, 18 Technical Manual – and then wonder why the blade stroke is off or a seal blows. This is the 52-page OEM document straight from Ferri. Not a reprint, not a hacked-up PDF from some forum. It covers the TR, TRM, 13, 22, and 18 models with the actual specs the factory uses. That’s what keeps the machine running and you out of the ditch.

Ferri TR, TRM, 13, 22, 18 Technical Manual: What’s Inside

Start with General Information (page 9) where they tell you how to identify the machine and order spare parts using the serial number – that alone saves you ordering the wrong blade. Then Technical Characteristics (page 13) gets into intended uses, contraindications, noise levels, and the part descriptions. The section on contraindications on page 13 tells you what not to do with this cutter bar. Pay attention to that; it’s not lawyer talk, it’s engineering reality.

Safety Rules — Not a Suggestion

Chapter 3 runs from page 17 to 26 and covers general safety, road traffic rules, hydraulic system safety, and the exact location of every safety decal on the machine. Page 26 shows you where those decals go and what they look like. If a decal is missing or faded, you replace it – the manual tells you how. Look at section 3.3.1: it’s specifically addressed to a new operator or owner. That’s the kind of detail you don’t get from a generic repair guide.

Adjustments: Change-Over Valve and Blade Stroke

Chapter 5 (page 35) is where the real work happens. The change-over valve setting adjustment, cutter bar blade stroke adjustment, blade change-over speed adjustment, and working speed adjustment are all laid out step by step. You need to know the correct stroke for the TR vs. the TRM – they are not the same. The manual gives you the sequence to check and set each one. Miss one step and you’ll eat up bearings.

Understand the Hydraulic Circuit Diagrams

Section 4.2 covers connecting the cutter bar for both open and closed circuits (page 30-31). If you’re hooking this to a tractor with a closed-center hydraulic system, you need to follow that procedure exactly. The hydraulic system safety rules on page 22 will keep you from getting a face full of hot oil. The manual also ties into your tractor’s Manual Transmission output – you need to match flow rates to avoid overspeeding the cutter bar. For deeper tractor specs, refer to your tractor’s Manual Transmission manual.

Does This Manual Cover the TRM Model?

Yes. The cover lists TR and TRM, and the table of contents shows model-specific information. Serial number codes on page 10 differentiate between 13, 22, and 18 variants. All adjustment procedures in chapter 5 apply to both open and closed circuit setups regardless of model. If you have a TRM with a different hydraulic configuration, the manual addresses it in section 4.2.2 for closed circuit.

Maintenance: Greasing, Troubleshooting, Blade Replacement

Ordinary maintenance starts on page 43 with a grease schedule – don’t skip the zerk fittings every 8 hours. The troubleshooting chart on page 46 is worth its weight in copper: it lists symptoms, causes, and fixes. Extraordinary maintenance (page 47) covers pipe replacement and cutting blade replacement (page 48). That’s where you really need the factory procedure to avoid snapping bolts or getting the blade timing wrong.

Every section is real, usable content. Page numbers are exact – no guessing where the info lives. This is the manual you keep on the bench, not in the office.

Related Manuals for Ferri Equipment

• FERRI ZMT/E Maintenance and Use Manual 2004
• FERRI ZME SHREDDER Maintenance and Use Manual
• FERRI TLP 160/200/250 Maintenance and Use Manual

FAQ

Is this the same as the operator’s manual?

No. This is the Technical Manual with specs and adjustments.

What torque values are listed?

The manual doesn’t list specific torque values in the TOC, but the Technical Characteristics section on page 14 includes hydraulic pressures and dimensions. For bolt torque, you’ll follow standard agricultural practices based on grade and thread size. The Safety Rules section (page 17) provides critical tightening procedures for hydraulic fittings. If you need exact values, check the change-over valve adjustment procedure on page 35.

Stop wasting time with aftermarket junk that leaves you guessing. Access the Factory Manual now and keep it on your bench. That’s the difference between a job done right and a comeback.