Description

Dynapac LF60 Parts Catalog – OEM Factory Spare Parts Reference

If you are ordering parts for a Dynapac LF60 vibratory plate compactor and you don’t have this catalog open on the bench, you are working blind. I have watched techs pull a “close enough” part from an aftermarket bin and then spend an afternoon chasing a vibration issue that was never there from the factory. That is wasted billable time and a machine that sits. This is the actual Dynapac LF60 Parts Catalog, 60 pages, printed by Dynapac (part of the Atlas Copco group). Every bolt, bearing, and seal is listed with its factory part number. No translation errors, no third-party renumbers.

Guessing costs more. That is a fact I learned twenty-eight years ago and it has not changed. When you need a new exciter assembly or a throttle cable for the Honda GX100 or Robin EH09 engine option, you pull the serial number from your machine, flip to the correct group page, and order the exact piece. The manual even tells you which catalogue issue applies—SLF060-2EN2 from 2009-04—so you are not working off an outdated revision. That kind of precision keeps the compactor running and the job moving.

Parts Catalog vs Service Manual: Know the Difference

This is not a repair guide. There are no torque specs, no step-by-step rebuild instructions, no wiring diagrams. What you get is a structured spare parts list organized by assembly group—engine, base plate, vibration system, handle, etc. Each part has a callout number, a description, and the factory part number you hand to your parts supplier or dealer. If you need the service procedure, you want the Dynapac shop manual for the LF60. But if you need the right part number, this is the only source that matters.

Why OEM Part Numbers Matter for the LF60

Aftermarket parts catalogs often combine multiple machine revisions into one generic entry. That is how you end up with a vibration damper that is 2 mm too thick or a carburetor gasket that does not seal. The Dynapac LF60 has specific serial number ranges—starting from 27600001—and two different engine variants. The OEM catalog breaks out every change. If your machine has serial number 27600150 with a Robin EH09, the part numbers are different from an earlier Honda-powered unit. The catalog shows that. You cannot get that from a reprint.

What the 60 Pages Cover

Page 3 shows the valid serial number ranges and catalogue issue dates. Page 4 gives the six-point ordering checklist—machine type, serial number, quantity, part number, denomination, and dimensions for length-cut items. That checklist alone prevents misorders. The rest of the catalog is divided into groups: engine parts, vibrator assembly, base plate, handle, and miscellaneous hardware. Each group starts with an exploded diagram and a corresponding parts list. Group 3 (notes and changes) is at the back. With 60 pages, every component is accounted for.

Ordering Spare Parts the Right Way

Follow the six-point list on page 4 every time. Write down the machine type (LF60), the serial number stamped on the frame, the quantity, the full part number, the denomination, and any length if the part is sold by the meter. Do not skip the serial number—that is what aligns your machine to the correct catalog revision. If you order by description alone, you risk getting the wrong engine variant parts. I have seen it happen. Use the factory part number and nothing else.

3 Sections You Will Use Most

First, the engine section—covers both Honda GX100 and Robin EH09 with separate part numbers for gaskets, pistons, and ignition components. Second, the vibration system—exciter housing, weights, bearings, and seals. Third, the base plate group—wear parts like the bottom plate and bolt-on dampers. Each section includes the exploded diagram so you can confirm you are looking at the right location before you order.

For larger compactors and cold planers, the same OEM accuracy applies. Check the Dynapac PL2000LS Parts Catalog (258 Pages) – OEM Factory Spec for the PL2000LS cold planer. That machine shares some hardware with the LF60 series. Also look at Dynapac PL2000LS Parts Catalog – Factory OEM Specs for Cold Planer for the cutting drum assemblies and the Dynapac PL2000LS Parts Catalog – OEM Spare Parts Listings for wear parts. All factory-original print, same standard as this catalog.

If you want to understand how Dynapac structures its spare parts documentation, start with this catalog. It follows the same logic as the larger machines. In the broader Automotive Industry Overview, parts accuracy is what separates a productive shop from a parts-chasing nightmare.

Is This Manual Right for Your Shop?

If you own or maintain a Dynapac LF60, you need this. Home garage guys who bought a used plate compactor and want to keep it running—yes. Fleet shops with multiple compactors—absolutely. The 60-page format is manageable. You can keep a printed copy in the parts room or the digital PDF on your tablet next to the machine. Either way, you stop guessing and start ordering the exact part the first time.

Does this catalog include repair procedures?

No. This is a parts catalog only.

How do I find the correct part number for my LF60?

You need your machine’s serial number. The catalog lists valid serial number ranges for each engine option—Honda GX100 or Robin EH09. Turn to the group pages for the assembly you need. Each part has a numbered callout and a corresponding part number. Match your serial number to the correct catalog issue (SLF060-2EN2 from 2009-04).

Can I use this to rebuild my plate compactor?

You can identify every part needed. For torque specs and assembly procedures, you need the service manual. The parts catalog shows you what goes where, not how to install it.

Is this a digital access?

Yes, you get a PDF of the original 60-page catalog.

Stop ordering parts blind. Access the Factory Manual now.