Description

Dynapac CC324CHF 2010 Parts Catalog – Factory OEM (479 Pages)

You’ve got a CC324CHF on the lift with a blown hydraulic hose and no idea which fitting goes where. Or you’re staring at a pile of vibration-drum parts and need the right eccentric shaft kit before lunch. I’ve been there—ordering the wrong part because some online list showed a different serial number range. That’s billable hours down the drain. This factory Dynapac CC324CHF 2010 Parts Catalog stops that nonsense cold. It’s the same binder the dealer parts counter uses, 479 pages of exploded diagrams and genuine part numbers for rollers with serial numbers from 10000316x0A000001 onward. No reprints, no third-party redraws—just the Swedish-original OEM data.

Page 1 makes it clear: this catalog is valid for CC324CHF rollers equipped with the Cummins QSB 3.3 diesel. If your roller falls in that serial bracket, you’re covered. Page 2 lays out the ordering procedure—machine type, serial number, part number, denomination. Follow that and you won’t get a box full of wrong bolts. I’ve seen guys skip the “dimensions when ordering per length” line and end up with a meter of hose that’s two sizes too small. Don’t be that guy.

Service Kits and Repair Kits – Factory Intervals

The manual breaks down service kits by hour interval: 50h (part 4700950174), 250/750h combo, 500h, and 1000h for the Cummins QSB 3.3. Each kit lists every filter, gasket, and belt you need. No guessing which oil filter cross-references. Repair kits include the eccentric shaft kit (4812155792) that fits CC224HF/324HF/384HF, the scraper kit (4700945908), and shock absorber kit (4812155158). If you’re rebuilding the vibration unit, you’ll find the exact bearing and seal part numbers in the Drum section.

Frame and Drum – Exploded Views for Every Module

Front frame, rear frame, sprinkler system, end frames—each module has its own exploded diagram with callouts. Need the steering cylinder? It’s part 4700391023, shown in the Hitch module. The scraper assembly with nozzles is listed separately from the one without. The drum section covers bearing, drive unit (including drum gear 4700392453), and vibrating unit. Every bolt and bushing is accounted for.

Engine and Hydraulic System – OEM Parts for Cummins QSB 3.3

Engine room breakdown includes the engine module, air cleaner, muffler, charge air cooler, expansion tank. Hydraulic system splits into front drum, frame, engine room, steering, and sliding seat steering. The hydraulic valve modules are listed with specific part numbers—4700395924 for the main valve, 4700391017 for the offset/combi valve. If you’re tracing a leak, these diagrams show every hose and fitting.

Electrical Equipment – Wiring Harnesses and Components

The electrical section covers power supply cables. While it’s not a wiring diagram manual, the parts catalog shows the harness routings and connector part numbers. Pair this with a factory service manual if you need electrical troubleshooting, but for ordering the right switch or relay, this is it.

Who Needs This Manual

Shop owners and fleet mechanics who maintain Dynapac rollers. If you’re a home-garage guy who bought a used CC324CHF at auction, you need this to keep it running without blowing your budget on wrong parts. The catalog uses imperial hardware where applicable (most fittings are metric on the Swedish-built machine, but check the dimensions when ordering per length). Beginners will appreciate the clear grouping: service kits first, then major assemblies, then detail modules.

OEM vs Aftermarket – Why This Matters

Aftermarket parts catalogs often redraw diagrams and skip hardware. This is Dynapac’s own publication, printed in Sweden. The part numbers are the ones stamped on the original components. If you order a 4700950174 service kit from a dealer, it matches this book. Counterfeit or third-party catalogs often use different numbering. I’ve had techs bring me a “compatible” part that didn’t fit because the aftermarket drawing missed a mounting bracket. Don’t waste money—use the real thing.

Related Manuals

• Dynapac CC324CHF Parts Catalog
• Dynapac CC324CHF 2010 Parts Catalog – OEM Factory Specification
• Dynapac CC324CHF Parts Catalog – Factory OEM 479 Pages

For more background on the manufacturer, see Dynapac and Automotive Industry Overview.

Is this manual just a list of part numbers, or does it show how to install them?

It’s a parts catalog – exploded diagrams and part numbers. It does not contain step-by-step removal or torque specs. You need a service manual for installation procedures. But if you need to order the right eccentric shaft kit or scraper assembly, this is the document to use.

What if my CC324CHF has a serial number below 10000316x0A000001?

This catalog covers rollers from that serial number forward. Earlier machines may have different parts. Check the Dynapac dealer or look for a prior edition (SCC324CHF-2EN1). The publication date 2010-10 supercedes the 2010-02 issue. If your roller falls outside the range, you’ll need a different catalog.

Stop tying up your phone searching online forums for a part number that might be right. Get the factory data on your bench. Access the Factory Manual now and start ordering with confidence that every nut and hose matches your roller’s build sheet.