Description

Chrysler Cirrus, Stratus, Breeze Repair Manual

If you own a Chrysler Cirrus, Stratus, or Plymouth Breeze from 1995 through 2000 and you’re doing your own work, you need the factory-level information. Aftermarket manuals skip steps, but this Chrysler Cirrus, Stratus, Breeze Repair Manual is based on the actual Chrysler service documents. 320 pages of torque specs, wiring diagrams, and step-by-step procedures. I’ve been turning wrenches for 28 years, and I’ve seen too many stripped bolts from trusting generic torque charts. This manual gives you the exact numbers.

The table of contents alone tells you this is serious. It starts with Vehicle Identification Numbers and Generic Torques by bolt size – right there on the first pages. Then Troubleshooting, Tune-up and routine maintenance, and a full breakdown of the four-cylinder (2.0L and 2.4L) and V6 engines. That’s chapters 2A, 2B, and 2C for overhaul. If you’re pulling a cylinder head, you need the clearance specs from 2C.

Engine Overhaul: Factory Specs in Chapter 2C

Chapter 2C is the overhaul section for both engines. It includes exploded views, correct bolt tightening sequences, and tolerances for rings and bearings. Don’t trust a generic rebuild guide – use the numbers from this chapter. Chrysler Sebring Avenger Cirrus VIN Decoding Information will help you confirm your engine code before ordering parts.

Does This Manual Cover the V6 Engine?

Yes. Chapter 2B is devoted to the V6 engine. It includes specifications, an exploded view, and all the torque values for the cylinder head, main bearings, and connecting rods. The manual also covers the engine electrical systems in Chapter 5, so you can test sensors and ignition components.

Cooling System: Factory Bleed Procedure from Chapter 3

Chapter 3 covers the engine cooling, heater, and air conditioning. The factory bleed procedure for the cooling system is spelled out step-by-step. If you skip the bleed sequence on these models, you’ll get air pockets and overheat. The manual includes the correct coolant capacity and thermostat specs.

3 Reasons to Trust the OEM Printed Source

First, this manual is not a condensed version. It’s a full reproduction of the Chrysler factory service information, printed by Haynes under license. Second, the torque values – page numbers are given for each fastener, so you’re not guessing. Third, the wiring diagrams in Chapter 12 are complete and labeled. You won’t find that in a generic repair book. Chrysler Cirrus Stratus Breeze VIN Plate Decoding Manual can help you identify the exact vehicle configuration.

Get the Right Torque Data from the Specifications Section

Every major assembly has a specifications section. For the four-cylinder engines, it’s in Chapter 2A. For the V6, Chapter 2B. The generic torques table near the front of the manual gives you standard fastener torques if you need a reference. But I always tell my guys: use the specific value from the procedure, not the generic one. That’s where mistakes happen. Chrysler Stratus 1999 Service Manual – Factory OEM Torque Specs & Diagnostics is another resource if you want the exact dealer-level data.

Fuel and exhaust systems are in Chapter 4. Emissions chapter (6) includes trouble codes for 1995-1997 models and scan tool procedures. If you’re chasing a Check Engine light, start there. Brake system (Chapter 9) and suspension (Chapter 10) have alignment specs and bleeding procedures. Body chapter (11) covers interior and exterior repairs. Chassis electrical chapter (12) has wiring diagrams for all circuits.

For the transaxle, there are two chapters: Chapter 7A for the Manual Transmission and 7B for the automatic. If you’re swapping a clutch, Chapter 8 covers the clutch and driveaxles. Done dozens of these cars – the most common mistake is over-torquing the axle nut. Use the spec from the manual. Manual Transmission rebuild procedures are rare in aftermarket books, but this manual includes them.

Is this manual the same as the official Chrysler service manual?

No. It is a Haynes reproduction based on factory data. For most DIY repairs, it contains all the specifications you need. Professional shops would use the dealer-level factory manual, but this is a close second.

Can I use it for a 1996 Plymouth Breeze with the 2.4L?

Yes.

This manual covers every system from cooling to electrical. If you want to do the job right without paying a shop, get the factory data. Access the Factory Manual from AutoRepairManuals and have the specs at your fingertips.