Description

Walker DGHS36, DSD36, DGHS42, DSD42, DML42 2000 Parts Catalog

Some people figure they can eyeball a part and order it by memory. That’s how you end up with a spindle that doesn’t fit or a blade bolt that strips out because you guessed the grade. If you work on Walker mowers for a living, you know the deck assemblies change by model and serial number. This is the Walker DGHS36, DSD36, DGHS42, DSD42, DML42 2000 Parts Catalog — an OEM factory document, not some aftermarket photocopy that ran through a fax machine twice. 48 pages, original print, published 11-02-00.

Every section in this manual comes straight from Walker Engineering. The table of contents lists each deck and carrier frame assembly by size and part number. You get exploded-view illustrations that show exactly how every washer, spindle, and belt routes. No guesswork, no cross-referencing from a third-party site that lists the wrong nut. The manual covers serial numbers DX-46813 thru DX-68358. If your machine falls in that range, this is the right document.

36 and 42 Inch Deck Assemblies: What’s Inside

Two decks for the 36-inch size: the DGHS36 (P/N 5710-15) and the DSD36 (P/N 5710-17). The 42-inch group includes the DGHS42 (P/N 5705), DSD42 (P/N 5707-10), and the DML42 (P/N 5707-11). Each assembly is broken down by its carrier frame first — the 36-inch frame is P/N 5710, the 42-inch is P/N 5700-10. Diagrams label every component with a reference number that ties to the parts list. Need a blade spindle for a DGHS42? Flip to that section, note the reference, and order the right Walker part. The same logic applies to the 48-, 52-, 54-, and 62-inch decks also included in this catalog.

Torque Specs and Loctite Application

Walker dedicated a full section to fastener torque instructions and Loctite application. This isn’t a generic chart — it’s specific to the fasteners used on these decks. The manual calls out required thread locker types and torque values in foot-pounds and inch-pounds. Skip this page and you risk over-torquing a spindle housing or under-torquing a blade bolt. The section also covers maintenance and service record sheets, plus lubrication points for all the fittings and pivot locations. If you’re rebuilding a deck from the carrier frame up, this section alone saves you from buying a new set of tapped holes.

3 Reasons to Use the OEM Parts Catalog

Reason one: the illustrated parts diagrams match the actual Walker deck in your shop. Reason two: the torque values come from Walker’s engineering team, not a forum post. Reason three: the deck/tractor compatibility chart at the back tells you which carrier frames mate with which tractors. This catalog also includes the mulching kit for the DSD52 deck — part numbers and installation parts listed. Combine that with the deck weldment replacement parts section and you have a complete sourcing reference for any deck overhaul. Aftermarket catalogs often combine 36 and 42 inch decks into one generic drawing. This manual keeps them separate and accurate.

Does This Manual Cover the DML42 Deck?

Yes. The DML42 deck assembly (P/N 5707-11) is listed right after the DSD42 section. It shares the same 42-inch carrier frame (P/N 5700-10) but uses a different spindle and blade arrangement for mulching. The illustration shows the differences in the belt path and idler pulley locations. If you’re converting a side-discharge deck to mulching, this section gives you the exact parts list for the DML42. You also get the decal and touch-up paint reference for each model — paint codes are listed for Walker’s factory colors so you match them correctly.

Fastener Torque Instructions: Not Optional

The fastener Loctite and torque page is where most aftermarket shortcuts fail. Walker specifies which grades of ESNA nuts and MS fasteners to use, and which threads need Loctite. The manual uses standard imperial units — foot-pounds and inch-pounds — with Newton-meter equivalents listed in the key to abbreviations. Every time I’ve seen a deck come loose or a spindle weldment crack, it traced back to the wrong torque or missing thread locker. This manual puts that information in your hands. Don’t trust a third-party reprint that might have dropped the torque column.

For related OEM documentation, check out these factory-issued parts catalogs:

• Walker MDD MDG 1996 Parts Catalog
• Massey-Harris-Ferguson FF 30 GS 1957 Parts Catalog | OEM Fastener Guide
• Futura FC200-FC400 Parts Catalog – OEM Wear Parts Specs

Understanding how fasteners behave under load is a core principle of Automotive Industry Overview, and Walker applies that same rigor to mower decks. Automotive Industry Overview may be broader, but this manual narrows it down to one brand and one model range.

Does this manual include torque specifications for the blade bolts?

Yes. The fastener torque section lists values for all critical bolts, including blade bolts. Refer to the Loctite and torque instructions page.

How do I find the correct part number for a worn spindle on a DGHS36 deck?

Turn to the section titled “36 INCH COMPLETE CARRIER FRAME ASSEMBLY (P/N 5710)” and then the “DGHS36 DECK ASSEMBLY (P/N 5710-15)”. The diagram shows every spindle part with a reference number. Match that number to the parts list for the description and Walker part number. The manual covers serial numbers DX-46813 through DX-68358. If your deck falls outside that range, check the deck/tractor compatibility chart at the back to see if a later revision applies.

This catalog is a working tool, not a shelf decoration. If you’re rebuilding a Walker deck or sourcing parts for a repair, you need the factory-issued drawings and specs. Access the Factory Manual and get the correct part numbers, torque values, and Loctite instructions from the source that built the deck.