Description

Linde 316, S30, S40, S50, S60 Operators Manual – What’s Inside

You have a Linde sideloader in the shop or in your warehouse, and you are staring at a control panel full of lights you don’t fully trust. Maybe you inherited the machine without a binder. Maybe the previous guy left and took his notes. Either way, you need the factory procedure for starting, driving, and maintaining these units — not a third-party rewrite that guesses at the LPG regulator settings. I have been turning wrenches for 28 years, and I have seen what happens when an operator ignores the factory daily inspection steps. You lose a cylinder head gasket because the coolant level was low and nobody checked it. You burn up a lift chain because the lubing spec was off. This Linde 316, S30, S40, S50, S60 Operators Manual is the original OEM document from Linde — 80 pages of German engineering translated into direct, actionable steps. No guesswork, no aftermarket interpretation.

Technical Data on Page 7 – What You Actually Need

Page 7 of this manual lists the technical data for each model. You get the tare weights, maximum travel speeds, lift capacities, and LPG system pressures. If you are swapping a tire or checking load capacity, you need those numbers. The manual also includes the tyre specifications for the drive axle and steering axle — found on page 23. Do not rely on a generic chart from a parts store. Use the factory values.

Starting the Engine: Normal and Cold Start Procedures

Starting an LPG engine is not the same as a gasoline engine. This manual walks you through the normal start sequence on page 25 and the cold-start procedure on page 25. There is also an emergency start method on page 26 if your battery is low or the starter relay fails. You also get the shutdown procedure and what to do if the motor stalls during operation. That section alone can save you a call to the dealer.

Daily Checks Before First Operation – Don’t Skip Them

Pages 19 through 23 cover the mandatory daily inspections: checking engine oil level, visual and odor inspection of the LPG system, verifying coolant level in the expansion tank, and checking brake fluid level. For the hydraulic system, you check the oil level on page 21 and know how to top it off on page 22. The manual also includes tyre pressure checks and the specific tyre specifications for drive and steer axles. If you are running a shop with multiple operators, make copies of this section and laminate them. It beats finding out your hydraulic pump is starving because nobody checked the reservoir.

Maintenance Schedule at 50 Operating Hours – Page 42

The first scheduled maintenance is after 50 operating hours. Page 42 lists the inspections and lubrication points required at that interval. After that, the overview on page 43 gives you the ongoing maintenance intervals. Tasks include cleaning and spraying the lift chains, checking the dust discharge valve, retorquing wheel nuts, and cleaning the water and hydraulic oil cooler. You also get procedures for securing the mast before any overhead work — an absolute safety requirement. This is not a scanner code; this is step‑by‑step text that tells you exactly which bolts to turn.

Why OEM Documentation Matters for LPG Forklifts

Aftermarket manuals often simplify the LPG system. Linde’s factory document includes the gas bottle change procedure, refilling from a bulk tank, and the daily gas system inspection. If you are using aftermarket documentation, you risk missing the odor check that can warn you of a leak before it ignites. You also get the manufacturer’s warning that only qualified, Linde‑authorized personnel should perform repairs — and that using non‑original parts voids warranty. For a shop, that is legal protection. For a DIY owner, that is safety insurance.

Is this manual in English?

No. This is the original German factory operators manual. English translations of headings and key warnings are not included. If you read German, you are set. If not, you will need a translator or rely on the diagrams and numbers.

Can I use this manual for a different model like the Linde H80?

No. This manual is specific to the 316, S30, S40, S50, and S60 sideloaders with LPG engine. Each model has unique load capacities, mast configurations, and control layouts. Using it for a different model will lead to incorrect procedures, potential safety hazards, and improper maintenance. For related models, see the Linde H100-600, H120-1200, H120-600, H140-1200, H160-600 Operators Manual, Linde H 50 T – 03 to H 80 T – 03 2005 Operators Manual – OEM Factory Specs, or Linde H 50-H80 2005 Operators Manual – OEM Factory Specs.

If you need background on how a Manual Transmission works or the basics of Cylinder Head Mechanics, those external resources cover general principles — but for your Linde sideloader, stick to the factory book. Access the Factory Manual now and keep it with the machine. Your operators will thank you, and your equipment will last longer.