Description

Iseki SSM48, SSM60, SSM54 2013 Parts Catalog – Factory-Sourced Part Numbers

If you are ordering parts for one of these Iseki mowers and relying on aftermarket websites, stop. I have seen more mis-sold bearings and wrong belts than I care to count because someone assumed a part number from a generic listing. This 23-page parts catalog from 2013 is the only source that has the correct factory codes for the Iseki SSM48, SSM60, SSM54 2013 Parts Catalog. You need the part code, not a description. A “case/lower” on a schematic can be two different items depending on your serial number. That is in here. Page 2 explains the head paragraph and how to read the interchangeability codes. If you skip that page, you are asking for returns.

CASE (BEVEL) SYSTEM – SSM48 vs SSM60 Differences

The catalog splits the case (bevel) system into two figures: one for the SSM60 (Fig. 2) and one for the SSM48 (Fig. 3). The SSM54 uses the same case as the SSM48. The illustrations show the upper and lower case halves, the pin (part code ¥623-100-801-26), and the bolt, sens (¥211-260-205-00). Notice that the SSM60 uses a different case/upper (8595-211-001-20) compared to the SSM48/54. If you order a case for the wrong chassis—TXG23E4 vs TXG23—you will be holding the wrong part. The catalog marks which parts are standard, optional, or replacement. Look at the SPC column on page 2: * means standard, T optional, R replacement. Do not guess.

PULLEY, BELT SYSTEM: Three Models Covered

Three separate figures are dedicated to pulley and belt layouts: Fig. 4 for SSM48, Fig. 5 for SSM54, Fig. 6 for SSM60. The belt lengths and pulley diameters differ between the models. You will also find the metal, blade system in Fig. 7 (SSM60) and Fig. 8 (SSM48,54). The blade part numbers are not interchangeable between the 48 and 60. Related parts for the TXG23 driveline are listed in the ISEKI TXG23 Service Manual if you need service specs, but for parts ordering this catalog is the final word.

MOWER DECK, COVER SYSTEM: Three Separate Figures

Fig. 9 covers the SSM54 deck and cover, Fig. 10 covers the SSM48, Fig. 11 the SSM60. Each deck has its own gauge wheel system—Fig. 12 for SSM48, Fig. 13 for SSM54/60. The link system (Fig. 14) and label diagram (Fig. 15) are common across models. The component parts section (Fig. 16) lists every fastener and bracket. This is where you find the exact part code for a missing retaining pin. Cross-reference the key number on the diagram with the part code table. It is not complicated, but it requires attention.

3 Reasons to Use the Factory Parts Catalog Instead of Aftermarket

First, the interchangeability column (ITC) tells you whether old parts can replace new ones or vice versa. On page 3, the catalog explains three codes: 1 (old ← new), 2 (old → new), 3 (old ↔ new not replaceable). Aftermarket databases often ignore these. Second, the GRP column shows which parts can be replaced as a set. Third, the color code (COL) is given for colored parts—without that code you may order the wrong shade of a decal or plastic cover. The Iseki SSM48 SRM48 SBC 350 Parts Catalog covers a different series; do not confuse them.

Get the Right Part Code – How to Read the Head Paragraph

Page 2 of the catalog has a section called “Explanation for head paragraph.” It explains the table columns: KEY, PART CODE, DESCRIPTION, SPC, TYPE OF MODEL (SSM48M, SSM48F, SSM48G, SRM48M, etc.), C, GRP, and REMARKS. The remarks column is not for jokes—it tells you if a part is supplied by meter (M) or liter (L) or is adjustable (AR). The serial number range is given in the lower column. For example, a part with a lower entry “-229” fits serial numbers up to 229; “230-” fits 230 and after. If you ignore serial number breaks, you will bolt an incompatible part. The Iseki SSM60-TH4330 SSM40M SSM50 SSM64M Parts Catalog is for different models, but the reading logic is identical.

Does this parts catalog include torque specs or service procedures?

No. This is a parts catalog, not a service manual. 23 pages of diagrams and part numbers only.

How do I find the correct part for my SSM48 if there are multiple variants (M, F, G)?

The catalog lists three variant columns: SSM48M, SSM48F, SSM48G (and the SRM-series equivalents). Look at the table on page 2. For example, part code 8595-211-001-20 CASE/UPPER is marked with an asterisk (*) in the SSM48M column and also appears under SRM48M. If your machine is an SSM48G, that part is not listed for G—you need part 8657-201-081-00 CASE/UPPER shown in row 1A. The SPC column tells you if it is standard, optional, or a replacement. Always check the SPC and type of model columns before ordering. The Automotive Industry Overview won’t help you—this catalog will.

You can also check Automotive Industry Overview for general context, but when you need the exact part code for a bevel case or blade system, go to the source. Access the Factory Manual.