Description

Gomaco GT-3600 Parts Catalog

You have a Gomaco GT-3600 down because the trimmer head belt snapped and you need the correct part number to order a replacement. Call three dealers and get three different answers. That’s wasted time. I’ve been turning wrenches for 28 years – ASE Master, six bays in San Antonio – and I’ve learned the hard way: you don’t guess on part numbers for heavy equipment. This is the real deal: the factory Parts Catalog, 500 pages, straight from Gomaco. No aftermarket redraws. No fuzzy scans missing the callout arrows. This is what the dealer parts counter uses.

Machine Assembly – Where the Part Numbers Live

First section in the TOC is Machine Assembly. That covers the basic machine assemblies for both the Cummins and John Deere engine versions. You’ll find part numbers and exploded views for the mainframe, legs, tracks, and the trimmer head. Page 1 of the catalog starts with the “BASIC MACHINE ASSEMBLY, CUMMINS” (part 902911-008) and the companion John Deere assembly (902911-014). Every fastener, bracket, and hydraulic line is listed. If you need the leg pivot assembly, it’s under Main Frame – part BT21-014. No paging through generic diagrams hoping the bolt callout matches your machine.

Engine – Cummins and John Deere Variants Covered

Two engine options on the GT-3600: Cummins and John Deere 4.5L. The Parts Catalog breaks them out separately. Look for the engine shroud assemblies – there are seven different versions depending on engine and year. You get part numbers for the control console assemblies too: Cummins consoles (902913-003, -007), John Deere consoles (902913-016, -022), and the newer CAN network consoles (902913-065, -066). This is not a generic “engine section” – each variant has its own part tree. If you need the block heater or the fuel filter head, the catalog pinpoints it.

Electrical System: Wiring and Control Consoles

Electrical section starts with junction boxes, display assemblies, and control boxes. Part BT29-045 is the junction box for the network control. The display assembly is 902920-033. If your GT-3600 has electrical gremlins – bad sensor feed, loose connector in the console – this catalog maps every harness connector to its part number. No aftermarket diagram guessing which wire pin goes where. You get the exact OEM part to order. That saves you pulling a harness off a wrecked machine and hoping it works.

TrimmerHead and Conveyor Sections

The TrimmerHead is the heart of the curb and gutter machine. The catalog dedicates a full section to it with part numbers for the cutting bits, gearbox, and mounting frames. Same for the Conveyor – belts, rollers, drive sprockets, all listed. Page numbers aren’t everything, but the index at the back lets you jump straight to the trimmer head assembly. Need a new belt? Look up the part number, call your dealer, done. Try that with a third-party manual and you’ll get a generic “conveyor belt, fits most models” – which fits nothing.

Why This 500-Page Parts Catalog Beats Aftermarket

I’ve seen aftermarket parts catalogs that redraw the drawings and change the callout numbers to avoid copyright. Then you order part “9423” and it’s actually the old superseded number. This OEM catalog from Gomaco uses the factory part numbers. The “Units of Measure” page on page 2 confirms all decimal dimensions – e.g., .625 in. for 5/8 in. bolts – so you know the fastener sizes are correct. Every fastener and seal is listed with the exact decimal equivalent. That matters when you’re ordering a hydraulic hose fitting and the thread pitch has to match.

Audience Fit – Who Needs This on the Bench

If you own or maintain a Gomaco GT-3600 curb and gutter machine, this catalog belongs in the truck or the office. DIY mechanics working on their own slipform equipment – you need the part numbers before you disassemble. Home garage enthusiasts with a dead machine? You’ll save hours not chasing wrong parts. Shop owners? Hand this to your techs instead of letting them guess and order twice. The catalog covers Hydraulics, Legs, Tracks, Options – basically every subsystem listed in the TOC. One example: the draw bar (902916-026) is 12 inches – that spec is right there in the parts list.

Related Manuals You Might Need

• Massey-Harris-Ferguson FF 30 GS 1957 Parts Catalog | OEM Fastener Guide
• Futura FC200-FC400 Parts Catalog – OEM Wear Parts Specs
• Longagribusiness 410 DTC, 450, 450 DTC, 470 DTC, 530 DTC 2002 Parts Catalog

For broader context on how manufacturing standards affect part numbering, check out the Automotive Industry Overview on Wikipedia. The same principles apply to heavy equipment: precision matters.

Does this Parts Catalog include torque specs for the engine?

No. This is a parts catalog, not a service manual. Torque specs and repair procedures are in the service manual.

What if I need to identify a part number for the trimmer head gearbox?

Go to the TrimmerHead section. Find the exploded diagram with callout numbers. Match to the part list. The gearbox part number is listed with its factory description. If your serial number falls within a range, check the “MACHINE SERIAL NUMBER” line on the cover page – some assemblies vary. The index at the back of the 500-page catalog cross-references every part number to the page. Takes ten minutes to find the correct number. That beats calling the dealer and reading them the serial number off the engine plate, then waiting three days for a callback.

Stop burning billable hours on wrong parts. Get the factory source. Access the Factory Manual from AutoRepairManuals today.