Description

Case 580M, 580 SUPER M, 580 SUPER M+, 590 SUPER M, 590 SUPER M+ 2010 Operators Manual

You want to run a Series 3 loader backhoe without guessing what every lever does? Good. Because this 263-page factory Operators Manual from Case gives you the exact procedures and specs that left the assembly line in 2010. No reprints, no aftermarket abbreviations – just the OEM document CNH America LLC printed under part number 84287120. If you have a 580M, 580 SUPER M, 580 SUPER M+, 590 SUPER M, or 590 SUPER M+, this is the manual that tells you where to put your hands and when to stop.

Safety Before Operation – Chapter 2 Content

Chapter 2 covers safety decals and the CALIFORNIA PROPOSITION 65 WARNING about diesel exhaust and battery lead. The manual uses three hazard levels: DANGER (red), WARNING (orange), CAUTION (yellow). If you ignore these, you’re betting against a machine that will win. Page 3 spells out the SAFETY ALERT SYMBOL – every operator must read and understand all decals before starting. I’ve seen guys skip this step and lose fingers. Don’t be that guy.

What Torque Specs Are Listed?

Chapter 8 – SPECIFICATIONS is where you find the numbers that keep bolts tight and fluid levels correct. The manual lists capacities in Imperial units – quarts, gallons, and foot-pounds. Need the charge pressure for the transmission? That’s in Chapter 8 alongside engine oil capacity, hydraulic system volume, and tire pressures. OEM torque values for wheel nuts and pivot pins are included. I will not guess a torque; you shouldn’t either.

Electrical System Diagnostics (Chapter 7)

Electrical problems on a loader backhoe can stall a whole jobsite. Chapter 7 – ELECTRICAL gives you the factory wiring diagram, fuse locations, and relay positions. You get the actual connector pinouts and wire colors as Case designed them. No aftermarket condensation of circuits. If you’re chasing a no-crank or dead instrument cluster, start here. Pair this with a multimeter and you can isolate a short without burning up hours.

3 Reasons to Choose OEM Documentation

Aftermarket manuals often rephrase notes and skip the California Proposition 65 warnings. This one retains every safety page, every decal explanation, and every fluid specification exactly as printed by CNH America LLC. You get the correct part numbers for filters, the proper lubrication intervals from Chapter 5, and the operator instructions that match the machine’s PIN. If you own a 2010 Series 3, this is the document your dealer would sell you.

Lubrication, Filters, and Fluids – Chapter 5 Walkthrough

Chapter 5 covers LUBRICATION, FILTERS, AND FLUIDS. It tells you which grease to use on the loader pivot points, the engine oil viscosity for San Antonio summers, and the hydraulic fluid type. Grease intervals are listed in hours of operation. Don’t mix fluids – the manual gives you the OEM part numbers. One reason I trust this manual is that Case printed it for the 580 SUPER M+ and 590 SUPER M+ variants, so you know the capacities match the machine’s actual hydraulic pumps.

Does This Manual Cover the Fuel System?

Yes. The operating instructions chapter (Chapter 4) includes starting procedures, cold-weather operation, and fuel system priming. For Manual Transmission models, the manual explains the shuttle shift pattern. For machines with a Supercharger Systems variant (if equipped), the manual does not cover aftermarket add-ons – only factory-installed components. The fuel system section is within Chapter 4, not a separate chapter, so you’ll need to cross-reference with Chapter 6 for injector timing adjustments.

FAQ

Does this Operators Manual include repair procedures like engine overhaul?

No. This is an Operators Manual – it covers daily operation, safety, lubrication, basic adjustments, and specifications. For engine teardown, get the corresponding Service Manual. This manual is for the guy running the machine, not the guy rebuilding it.

What page shows the hydraulic oil capacity for a 580 SUPER M+?

Page 73 of Chapter 8 lists hydraulic system capacities for all models – 580M, 580 SUPER M, 580 SUPER M+, 590 SUPER M, 590 SUPER M+. You get the reservoir capacity and total system volume in gallons.

Can I use this manual for a 2008 model?

This manual is specifically for Series 3 machines with a 2010 publication date. The 2008 model may have different decals or instrument clusters. Check your machine’s PIN against the manual’s coverage. The primary models (580M, 580 SUPER M, 590 SUPER M) share many specs, but the 580 SUPER M+ and 590 SUPER M+ have unique features.

Why should I buy this factory version instead of a third-party PDF?

Because the third-party PDF might omit the California Proposition 65 warnings and safety decal illustrations. This OEM manual from Case Construction retains every page – including the SAFETY ALERT SYMBOL explanation, the exact wording for DANGER/WARNING/CAUTION, and the official CNH copyright. If you ever have a safety audit or an injury, a factory manual is your only defense. Access the Factory Manual.

Your machine deserves the correct information. This 263-page Operators Manual for Case 580M, 580 SUPER M, 580 SUPER M+, 590 SUPER M, and 590 SUPER M+ Series 3 loaders backhoes (2010) will sit on your seat box or phone tablet and answer every question that matters – from how to engage the differential lock to what the electrical fuse panel looks like. I run a six-bay shop in San Antonio, and I’ve told every new tech: get the factory manual before you touch the machine. Access the Factory Manual now and keep it in your tool box.

• Related Manuals:
• CASE 580M Parts Catalog – Section: Index
• CASE 580M SERIES 3 2008 Parts Catalog
• CASE 580M 580M TURBO 2006 Operator’s Manual