Xtreme Manufacturing XR4030 Parts Catalog – 225-Page OEM Part Numbers

Description

You’ve got a blown hydraulic line on an Xtreme Manufacturing XR4030 Parts Catalog telehandler, and the parts counter wants a number you don’t have. Or you’re rebuilding the Engine and need the exact head bolt part before you order. That’s where this 225-page factory parts catalog stops the guesswork. It’s not a service manual – it’s the parts bible for the XR4030, straight from Xtreme Manufacturing, with every component drawn and numbered so you can match hardware without holding a tape measure against a faded casting mark.

Section 2 – Chassis: Frame Numbers, Fasteners, and More

If you’ve ever ordered a frame bolt by eyeballing it, you know the fun of getting a 12.9 when you needed a 10.9. This catalog breaks down the chassis section (pages 6–31) with exploded views of the frame, counterweight mounts, and undercarriage. Every fastener has a listed size, grade, and Xtreme Manufacturing part number. The abbreviations table on page 5 gives you the thread coding – UNC vs. UNF – so you can confirm before you click Buy.

Section 4 – Engine: Part Numbers for the Powerplant

The Engine section (page 45) covers everything from the air cleaner bracket to the oil pan gasket. You’ll need this if you’re chasing down a coolant leak and the local dealer says, “We need the serial number and the part suffix.” The catalog shows the complete assembly tree, including bolt torque callouts for the cylinder head (listed in the specs on page 48). No aftermarket hack job – this is the same drawing the factory uses at the assembly line.

Section 5 – Transmission, Axles, & Driveshafts: When the Powertrain Stops Moving

If you’ve got a whine from the Transmission or a leak at the axle seal, you need the right seal and bearing numbers before you pull the half-shaft. This section (pages 55–65) shows the internal breakdowns of the ZF transmission, the drive axles, and the coupling shafts. Each planetary gear set is exploded, with the Transmission pump, filter, and housing identified. Use the index starting on page 168 to cross-reference a part number if you only have the description.

Section 8 – Electrical System: Wiring Harness Part Numbers

The Electrical section (page 97) is where most aftermarket catalogs fall flat. They show a generic harness silhouette and tell you to call for details. This catalog gives you the factory harness layout, connector part numbers, and the exact terminals for the Deutsch DT connectors. If you’re chasing a short and need to replace a pin, page 103 lists the wire gauge, part number, and crimp tool spec. That saves hours of tracing with a multimeter.

Section 11 – Attachments: Bucket and Fork Part Identification

Quick-attach plates, bucket wear bars, fork tine pins – they all wear out, and they all have specific part numbers. This section (pages 162–167) covers the factory attachment line. The hydraulic quick-coupler assembly is broken down into valve block, cylinder, and pin sets. You match the part number to the serial number range stamped on your XR4030 frame (located per the chassis section).

Who Needs This Parts Catalog?

If you’re a home garage mechanic keeping a telehandler running on a farm or job site, you’re the exact target. The parts counter at the dealership will ask for the serial number and then tell you to buy an assembly you don’t need. With this catalog, you order the seal, not the whole motor. The exploded views are drawn to scale, and the part numbers are cross-referenced in the index. No more returning parts because the bolt length was off by 5 mm.

Factory OEM Print vs. Aftermarket Copies

Every time I see a reprint from a third‑party seller that claims “from original source,” I check the bolt torque table. If the torque values are in Nm only and missing the ft‑lb conversion, I know it’s a scan of a scan. This is a direct factory file from Xtreme Manufacturing – the 225 pages are clean, the drawings are crisp, and the abbreviations (page 5) match SAE standard. You get the same document the dealer pulls up when you stand at the counter.

Related Manuals

If you’re working on a smaller telehandler, check out the Xtreme Manufacturing EZ24 2008 Parts Catalog for the mid‑size platform. The Xtreme EZ18 2007 Parts Catalog covers the compact unit, and the Xtreme Manufacturing EZ18 2007 Illustrated Parts Catalog includes color-coded diagrams for the hydraulic system.

For background on telehandler design standards, see the Automotive Industry Overview page and Automotive Industry Overview for the engineering principles behind mobile equipment.

Frequently Asked Questions

Does this catalog include torque specifications or just part numbers?

It is a parts catalog – exploded views, part numbers, and quantities. Torque values appear only where they affect fastener selection (e.g., cylinder head bolts on page 48). For service procedures you need the XR4030 Service Manual, which we also carry.

Can I identify the exact bolt I need if I only have a part number from the old contractor?

That’s the whole point. Look up the part number in the index (pages 168–193) – it will tell you the section, page, and position. No guesswork.

Does the manual cover the electrical harness for the Tier 4 final engine?

Yes. The Section 8 – Electrical System includes the harness for the diesel particulate filter (DPF) sensors, the ECU, and the cab controls. Pages 103–110 show the connector view and wire routing.

What if I can’t find the part I need in any section?

Check the Addendum starting on page 194. Xtreme Manufacturing added late‑model revisions and superseded part numbers there. If it’s still missing, call a dealer with your serial number – but the catalog covers 99% of the XR4030 variants.

You can spend an afternoon hunting for the right part number online, or you can open this factory catalog, find the exploded view, and order the exact component. That’s why I keep a copy in the shop binder. Access the Factory Manual now and have the part number ready before you pick up the phone.