Terexlift SP950 1977 Parts Catalog – OEM Diagrams & Part Numbers

Description

Spent an afternoon chasing a part number for a 1977 Terexlift SP950 vibratory roller? I’ve been there. Aftermarket parts lists leave out details—wrong seals, mismatched fasteners. That’s time burned and money wasted. This Terexlift SP950 1977 Parts Catalog is what you need on the bench. It’s the factory-issued document, 60 pages thick, serial-number-specific (95HX505 and up). No reprints, no guesswork. Just OEM part numbers and exploded views that match what you’re holding.

Power Unit Components and Mounting

You’ll find the engine section on page 7 of the index grid. It lists the General Motors 3-53 diesel (model 5033-7201) with all adjuncts: air cleaner, muffler, battery, and hydraulic pump mounts. Page 4 in the actual catalog shows the exact part numbers for the front engine support cap screws (1/2 x 3” UNC), the rubber center-bonded mount (Lord #J-6256-3), and the exhaust outlet flange with 3” pipe threads. If you need to order a replacement air inlet housing gasket (part 5124405), it’s right there. That level of detail keeps you from buying the wrong part.

Does This Catalog Cover the Hydraulic Systems?

It does. The steering components section includes the articulating joint, cylinder, hydraulic pump, and valve. The traction drive section breaks down the hydrostatic pump, motor, two-speed transmission, and differential. For the vibration drive, you get the M.D.F. control cylinder, the hydraulic motor and pump, plus the variable volume pump assembly. All parts are keyed to fische numbers and grid coordinates. You can identify the exact seal kit or piston assembly without cross-referencing third-party numbers.

7 Critical Sections in This OEM Reference

• Control Console Assembly – includes wiring diagrams (page 28 and 30) for the speedometer and hydraulic lines
• Fluid System – covers fuel oil tire wetting, pump, strainer, tank and piping
• Power Unit – engine mount, air cleaner, battery, muffler, and controls
• Steering Components – cylinder, valve, articulating joint, and hydraulic pump
• Traction Drive – differential, drive train, hydraulic lines, hydrostatic motor and pump, wheel options
• Vibration Drive & Controls – M.D.F. roll, hydraulic motor, transducer assembly
• Roll Over Protection – structure and mounting

That’s seven sections covering everything from the fuel system to the wiring harness. Every part has a factory part number and quantity. No generic descriptions.

Wiring Diagrams: Factory-Correct Routing

Electrical gremlins on a 1977 machine? The wiring diagrams on pages 28 and 30 show the exact harness routing, connector types, and wire colors. You won’t find that in a reprint. This catalog was printed in October 1977 by Rexnord Inc., Milwaukee. It’s the same document that dealership parts counters used. If you’re tracing a short or replacing a damaged loom, this is your reference.

Use the Index to Find Parts Fast

Page 2 contains the full index with grid numbers. Each section lists the page range. The engine and mount section is on page 1 according to the grid? Actually it’s listed as page 1 under Power Unit. The fluid system starts on page 49 for the pump, page 50 for tank and piping. The steering valve is on page 24. You can go straight to the right page without flipping through the whole book. That matters when the machine is down and the boss is watching.

One thing I’ll hammer home: always give the serial number when ordering. This catalog covers SP950 rollers from serial 95HX505 and up. If your machine is older, you need the earlier edition. That’s why we link to related manuals: 1972 Terexlift S.P. VIBRATORY ROLLER Parts Catalog – OEM Factory Reference and Rex SP848 SP900 Vibratory Roller Repair Parts Book and Rex SP848B Vibratory Roller Parts Book (1982).

I trust OEM documentation because I’ve seen aftermarket catalogs swap a 5/8” cap screw for a 9/16” and blow a mounting bracket apart. This manual was printed by the manufacturer. It’s not a scan of a scan. For a broader look at how heavy equipment parts catalogs fit into the repair industry, check the Automotive Industry Overview and Automotive Industry Overview.

FAQ

Can I use this catalog to find torque specs for the cylinder bolts?

This is a parts catalog, not a service manual. It lists part numbers and exploded views. Torque specifications are not included. For torque values, you need the factory service manual for that model.

Does it include the wiring diagram for the entire machine?

Yes. Pages 28 and 30 show the full wiring diagram for the control console and power unit. It covers the speedometer, hydraulic lines, and all electrical connections.

What serial numbers does this cover?

Serial 95HX505 and up. Check your machine’s plate before ordering.

Is this an original OEM print or a reproduction?

Original OEM print from Rexnord Inc., October 1977. 60 pages, no reprint, no copy.

You need the part numbers that match your machine. Stop guessing with generic online listings. Access the Factory Manual and get the right component the first time.