Description

Jeep Liberty 2008 Parts Catalog – 515 Pages of OEM Factory Data

If you’ve ever ordered a replacement part for a Jeep Liberty and ended up with the wrong one because you guessed the VIN code or trusted an aftermarket catalog, you know exactly why this document exists. The 2008 Jeep Liberty 2008 Parts Catalog is not a repair manual. It’s a factory-issued parts reference that tells you exactly which MoPar part number bolts onto your Liberty based on the VIN. 515 pages of OEM data, not aftermarket approximations. That’s the difference between a job that fits and one that fights you.

VIN Plate Decoding: The First Step

Page 1 of this catalog lays out the VIN plate decoding table. Position 8 tells you which engine you have: K for the 3.7L V6 Magnum gas, E for the 3.0L turbodiesel. Position 5 decodes drivetrain: P for left-hand drive 4×2, N for left-hand drive 4×4. If you order a front axle shaft for a 4×2 and your Liberty is a 4×4, you’re wasting time. This table kills that guesswork. The rest of the catalog groups parts by VIN-derived codes, so every figure you look up applies to your specific build.

MoPar Accessories: Not Just Add-Ons

Group 1 covers MoPar accessories with figure numbers for each kit. Navigation kit (Fig. 1-108), satellite receiver install kit (Fig. 1-114), iPod integration (Fig. 1-122). Need a wiring kit for off-road lights? Fig. 1-264. The catalog gives you the part number, not a “universal” harness that requires splicing. If you’re adding factory accessories to a Liberty, you want the exact harness that plugs into the existing connectors. That’s what this section delivers.

Front Suspension and Axle Groups: What’s Covered

Group 2 covers front suspension including the strut and cradle (Fig. 2-110) and stabilizer bar (Fig. 2-210). Then Group 003DJJ details the Dana 186MM front axle assembly – housing and vent (Fig. 003DJJ-210), differential assembly (Fig. 003DJJ-220), drive shaft (Fig. 003DJJ-610). Group 003DRA covers the Corporate 210MM rear axle, including the one-piece drive shaft (Fig. 003DRA-610) and housing (Fig. 003DRA-810). Each figure breaks down every bolt, seal, and bearing with an OEM part number. No cross-referencing aftermarket databases.

Brake System Parts: Factory Diagrams

Group 5 breaks down the brakes into front (Fig. 5-111), rear disc (Fig. 5-212), master cylinder (Fig. 5-410), and hydraulic control unit with tube routing for left-hand and right-hand drive (Fig. 5-507, 5-511). The parking brake lever and cables (Fig. 5-711) are separated from the rear disc park brake assembly (Fig. 5-731). If you’ve ever had a brake line leak because you used a generic tube instead of the factory‑bent line, you’ll appreciate the exact tube routing diagrams in this catalog.

Clutch and Cooling: Torque Specs You Can Trust

Group 6 covers the clutch assembly (Fig. 6-111), clutch housing for the EKO and ENO engines (Fig. 6-220, 6-221), and hydraulic clutch controls (Fig. 6-311). Group 7 handles cooling: radiator (Fig. 7-105), water pump (Fig. 7-205), thermostat (Fig. 7-250), serpentine belts (Fig. 7-505). These are not repair procedures – they are parts breakdowns. But the part numbers come from the same engineering drawings as the service manual. A water pump gasket ordered from this catalog will match the casting exactly.

Source Authenticity: OEM vs. Aftermarket Catalogs

Aftermarket parts catalogs often combine multiple years or skip the VIN‑specific variations. This document was published by Jeep in 2008 for the 2008 model year Liberty. It uses the same part numbering system as the factory assembly line. If the aftermarket says “fits 2002‑2008 Liberty,” you don’t know if you’re getting the 2002 front axle or the 2008 revision. With this catalog, the VIN tells you exactly. No reprints, no third‑party data – just the original PDF of the factory parts catalog.

For related documentation, check the 2005 Jeep Liberty (KJ) Service Manual if you need repair procedures, or the 2002-2007 Jeep Liberty KJ Service Manual for earlier models. If you’re looking for an older parts reference, the Jeep Liberty 2002 Parts Catalog covers the first generation. The broader Automotive Industry Overview provides context for how OEM parts catalogs are structured. Automotive Industry Overview

Frequently Asked Questions

Does this catalog include wiring diagrams or repair instructions?

No. This is a parts catalog, not a service manual. It contains exploded‑view diagrams and part numbers for ordering, not step‑by‑step repair procedures.

Can I use this to identify parts for a 2008 Liberty with the 3.7L engine?

Yes. The VIN decoding table on page 1 breaks down every position. Position 8 code K identifies the 3.7L V6 Magnum gas engine. From there you navigate to the appropriate group figure for your specific engine and drivetrain combination. This catalog covers both the 3.7L gas and the 3.0L turbodiesel, so make sure you decode your VIN correctly before ordering. If the VIN says engine code K, go to the figures that reference the 3.7L components – the part numbers are unique to that engine. The front axle and brake parts also vary by build, so always start with the VIN.

You need a parts catalog that doesn’t leave you guessing. Access the Factory Manual and get the exact part numbers for your 2008 Jeep Liberty. It’s 515 pages, VIN‑specific, and direct from the manufacturer.