Description

Fiat-hitachi AERIAL WORK PLATFORM, BULLDOZER, CRAWLER EXCAVATOR, CRAWLER CRANE, CRAWLER CRANE DRAGLINE 2008 Technical Manual

I’ve been turning wrenches for 28 years. When you’re working on a Fiat-hitachi AERIAL WORK PLATFORM or a BULLDOZER, you don’t guess on filter numbers. You grab a manual that lists the Donaldson replacement for every air, fuel, hydraulic, lube, and coolant filter. That’s what this 44-page Technical Manual is. It’s a factory vehicle card from 2008, not some aftermarket reprint. It covers the CRAWLER EXCAVATOR, CRAWLER CRANE, and CRAWLER CRANE DRAGLINE models too. If you’re swapping filters blind, you’re asking for a plugged system or a bypass failure. This manual stops that.

Aerial Work Platform: Filter Listings for HX 99B, HX 140B, HX 220B

Starting on page 1, you get the part numbers for the HX series. For the HX 99B with a Kubota D1105-BH, it lists the air primary (P822686), fuel cartridge (P502134), three hydraulic cartridges, and a lube spin-on (P550162). The HX 140B and HX 220B follow with their own specs. The HX 220B uses an Isuzu 4BG1-PG02 engine, so the air filter is a P543662 axial seal, not the radial seal used on the smaller machines. That kind of detail keeps you from ordering the wrong part.

Bulldozer D180: Engine and Hydraulic Filters

The D180 bulldozer gets a full page. Cummins 6CT8.3 engine. The manual lists an air primary (P772587), secondary (P770678), coolant spin-on (P554071), fuel/water separator (P551329), fuel filter (P550440), and multiple hydraulic cartridges. Note the fuel/water separator – it’s a spin-on, not a cartridge. If you don’t know that, you’ll end up with a leaky setup. Page 2 covers this.

Crawler Excavator EX60: Air and Fuel Filters

Two versions of the EX60 are listed. The EX60 with Nissan FD3304 uses an axial seal air primary (P181052) and a fuel filter spin-on (P553240). The EX60(LC)-5 with Nissan BD3004-19 switches to a radial seal air system (P822768 primary, P822769 secondary). That’s a critical difference – if you try to force a radial seal into an axial housing, you’ll get dirt ingestion. The manual also lists the hydraulic cartridges: P173238, P4225846, and the lube spin-on P550008. All from the factory.

Crawler Crane Dragline: What the Manual Covers

The CRAWLER CRANE DRAGLINE section starts on page 5. The manual doesn’t give you a full tear-down procedure. It’s a vehicle card – a cross-reference of filter and part numbers. That’s exactly what you need when you’re at the parts counter. You get the Donaldson OE numbers for each application. No guessing. Crawler Crane operations rely on clean hydraulic oil. A wrong filter can cost you a day of downtime.

Source Authenticity: OEM vs. Aftermarket Filter Cross-References

I’ve seen aftermarket manuals that list generic part numbers. They don’t tell you the seal type or the thread pitch. This one is a Donaldson vehicle card – it’s the same document the dealer uses. It was published in 2008 by Fiat-hitachi, so it’s factory spec. Fiat-hitachi ZX800 Technical Manual – OEM Factory Specs is another manual that gives you the same level of detail for the ZX series. If you’re serious about keeping your equipment running, you don’t use a knock-off guide.

Who Should Buy This 2008 Technical Manual

If you’re a mechanic who works on Hitachi construction equipment, or a shop owner who maintains a fleet of AERIAL WORK PLATFORMS and BULLDOZERS, this manual saves you the phone call to the dealer. It’s 44 pages, but every page is dense with application-specific part numbers. For the home garage enthusiast who owns an older EX60, this is the difference between a Sunday afternoon job and a week of waiting for the wrong part. Fiat-Hitachi 40U-2 50U-2 Technical Manual – 349 Pages OEM covers a different machine family, but if you work on those, grab it too.

Frequently Asked Questions

Does this manual include torque specs for filters?

No. This is a filter cross-reference, not a service manual. It lists Donaldson part numbers, not installation torque. Use a separate manual for that.

Can I use this manual for my EX60-5?

It covers the EX60(LC)-5 with the Nissan BD3004-19 engine. If your serial number matches the range in the manual, yes. The manual is from 2008, so it may not include later revisions. Check the OE number against your machine’s filter. If it matches, you’re good. If not, you’ll need a newer card.

Why is the manual only 44 pages?

Because it’s a vehicle card, not a full technical manual. It lists filters for multiple models in a compact format. Each model gets a few lines. That’s all you need to order the correct Donaldson filter. No fluff, just part numbers.

What filter types are covered for the CRAWLER CRANE DRAGLINE?

The manual covers air primary, air secondary, fuel, hydraulic, lube, and coolant filters for the CRAWLER CRANE DRAGLINE models listed in the index. Each entry specifies the OE number and the Donaldson replacement number. For example, if you have a dragline with a specific engine, you’ll find the correct filter. The manual does not include the dragline’s full specifications, only the filter cross-reference. This is typical for a vehicle card. It’s designed to be used alongside the service manual. If you need the dragline’s hydraulic system pressure, you’ll need a different manual. Fiat-hitachi EX135 1998 Technical Manual – OEM Function Description might help with function descriptions.

Bottom line: if you’re working on any of these machines, you need the right filter part numbers. This manual gives you that. Don’t risk a $10 filter taking out a $10,000 pump. Access the Factory Manual today.