Description

Case 585, 584, 586 2001 Operators Manual – OEM Specs for Hydrostatic Drive Forklifts

I’ve lost count of how many times a guy shows up in my bay with a forklift that “just stopped moving” and he’s got a stack of photocopied reprints from some third-party site. The numbers are wrong, the fluid capacities are guesswork, and the safety decal descriptions don’t match what’s actually on the machine. That’s a liability. If you run a Case 585, 584, or 586 2001 Operators Manual on your hydrostatic drive forklift, you need the real thing – the OEM document that Case printed when this machine left the factory. This 40-page manual is the exact reprint of that factory book. No retyping. No reinterpretation.

Safety Rules: The Difference Between Danger, Warning, and Caution

Page 2 spells out exactly what those red, orange, and yellow decals mean. Case uses both ANSI and ISO two‑panel pictorial decals. The manual tells you the first panel shows the hazard, the second shows avoidance. Background color is yellow. Prohibition symbols are red. If your machine has the older “Danger – Warning – Caution” set, you get the definitions: red for immediate death or serious injury, orange for serious injury, yellow for minor to moderate. I’ve seen operators ignore a yellow decal because they thought it wasn’t critical – that’s how you lose a finger in a hydrostatic drive system. This manual makes it clear, and it’s your responsibility to check every decal against the book.

Serial Number Location and Machine Orientation

The “Serial Number Location” chapter shows you where to find the plate on your 584, 585, or 586. Don’t assume it’s on the dash – Case sometimes stamps it on the frame rail near the battery box. The “Right-Hand and Left-Hand” section defines orientation from the operator’s seat facing forward. That sounds basic, but I’ve had arguments over which side the hydraulic reservoir cap is on. Get it from the manual before you start ordering parts.

Specs for Three Models: 584, 585, 586

Page 7 starts the specifications section. It covers dimensions, operating data, and individual model specs for each of the three machines. The 584 has a different turning circle and travel speed than the 585 or 586. Tire sizes, fuel capacity, hydraulic system pressure – it’s all broken out model by model. If you’re swapping a tire on a 585, you need the right ply and load rating listed on page 10. The turning clearance circle diagram on page 11 will save you from ripping off a fender in a tight warehouse aisle. The travel speeds table is critical for hydrostatic drive diagnostics – if the machine won’t reach its listed speed, you’ve got a pump or motor problem, not an engine issue.

Operation Instructions and Hydrostatic Drive

The “Operation Instructions” chapter covers start-up, shutdown, and basic controls for the hydrostatic transmission. It includes the correct procedure for releasing the parking brake and engaging the drive pedal. Do not skip the warm-up step – the hydrostatic fluid needs to circulate before you put a load on the forks. The manual also notes the location of the ROPS structure and any extra equipment like side shifters or fork positioners. If your machine has aftermarket additions, check the “Extra Equipment” section to see if Case approved them for that serial number range.

Maintenance and ROPS – Factory Requirements

Maintenance intervals are listed in the manual, but what I really want you to pay attention to is the ROPS (Roll Over Protective Structure) section. That canopy is not a decoration. If it’s been modified, welded, or drilled, the entire structure is compromised. The manual states that any modification voids the ROPS certification. Same goes for seat belts – if the machine has a ROPS, you need a seat belt. Period. The maintenance section also includes fluid change intervals, filter part numbers, and lubrication points. All factory data, not aftermarket guesses.

Trust OEM Documentation Over Reprints

This manual is a direct reprint of the original 2001 Case publication (part number 9-4242, reprinted March 1995 revised October 1997). The OCR excerpt on the site shows the exact safety definitions and table of contents. No one has retyped the specs. No one has “enhanced” the illustrations. What you get is the same document the Case dealer used when this machine was new. If you’re looking for a workshop manual with torque specs and rebuild procedures, check the Case International 385 485 585 685 885 Workshop Manual – that one covers engine and drivetrain overhaul. For a simpler daily reference, the Case 584/585/586 Power Shuttle Forklift Operators Manual covers the power shuttle version. And the Case 885, 385, 485, 585, 685 Workshop Manual – OEM Shop Service is the full service manual for the same family. But for daily operation and basic maintenance on the hydrostatic drive models, this operators manual is the one you keep in the cab.

Does this manual cover the 584, 585, and 586 models equally?

Yes. Specifications are listed separately for each model on pages 7 through 10.

Why should I buy the OEM reprint instead of a generic manual?

Because a generic manual might tell you the hydraulic pressure is 1500 psi when Case says 2000 psi. That difference blows seals. This manual is a photocopy of the original factory book – same safety decal positions, same fluid capacities, same tire ratings. I’ve seen three different aftermarket “operators manuals” for the 585 that all show different travel speeds. The only one that matches the plate on the machine is the OEM reprint. If you want to argue with my experience, go ahead – but your oil cooler will thank you when it doesn’t overheat from wrong fluid spec.

You don’t need to guess about whether your 584, 585, or 586 is safe to operate. You don’t need to wonder if the fluid capacity on a forum is correct. The factory printed the answers in 2001, and this is that exact document. Manual Transmission knowledge helps, but a hydrostatic drive is a different animal – you need the OEM instructions. Manual Transmission basics won’t get you through a pump failure. What will get you through is having the factory operators manual in your hand. Access the Factory Manual now and keep it with the machine.