Description

Case 1150D, 1155D 1995 Operators Manual – Factory Specs & Safety

Listen. I’ve seen too many guys jump on a Case 1150D, 1155D 1995 Operators Manual and think they can skip reading it because they’ve run a dozen other machines. Then they hit a control they don’t understand, dump a bucket wrong, or forget the parking brake procedure. That’s how machines get bent and people get hurt. This is the factory manual, 120 pages, printed by Case Corporation in 1995. It’s the same book that came strapped to the machine when it left the factory. No aftermarket reprint, no third-party guesswork. You want to run a 1150D or 1155D safely and keep it in one piece? You start here.

Safety First: Personal and Machine Protection

The first fourteen pages of this manual hammer home what you need to know before you even touch the key. Page 4 starts with Personal safety. Page 5 tells you what to check before starting the engine – and that’s non-negotiable. Page 6 covers engine starting procedure, including the warning about clearing the area of other persons. If you’ve ever seen a clutch grab unexpectedly because someone bypassed the neutral safety, you’ll appreciate why these pages exist. This section also covers ROPS (Rollover Protective Structure) on page 14, cold iron parts on page 16, and the spark arrestor on page 17. Ignore those and you’re betting your life against a weld failure. I don’t like those odds.

Operating Instructions: Instruments and Controls (Page 18)

Page 18 kicks off the operating instructions with instruments and controls. This isn’t a generic layout – it’s specific to the 1150D/1155D dash. You get diesel engine starting steps on page 19, loader floor pedals on page 20, and machine controls on the same page. The control tower and accelerator are detailed on page 21. If you need to adjust the seat, page 22 covers seat and seat adjustment. The master disconnect switch and pilot controls sit on that same page. Dozer control levers are on page 23, tilt gauge and parking brake on page 24, winch controls on page 24, suspension seat on page 25, and operator seat belt on page 26. That’s almost a dozen critical systems packed into ten pages. Miss one step – like forgetting to engage the parking brake before leaving the cab – and you’re chasing a runaway crawler.

Loader and Dozer Controls: Pages 29–36

For anyone running a loader or dozer attachment, pages 29 through 36 are your bread and butter. Loader controls start on page 29 with raising and lowering the bucket page 30, one-side rock or dump on page 31, bucket tilt on page 31, bucket level indicator on page 31, and the Reback-o-Dig feature on page 31. The 4-in-1 bucket is covered on page 32 with bucket and clamp indicator on page 33. Then dozer controls take over: hydraulically actuated dozer controls on page 33, control lever for lift and tilt on page 33, control lever for tilt only on page 34, control lever for lift-tilt-pitch on page 35, and control lever for angle on page 36. This is not a theoretical overview – it’s the exact sequence of levers and pedals you’ll use every shift. If you’re unfamiliar with how the Reback-o-Dig works, page 31 will save you from tearing up the undercarriage.

Transmission and Steering: Pages 37–40

Transmission controls start on page 37 with accelerator/emergency use, control lever for speed and travel, and transmission gear selection. Page 38 continues with transmission controls, then page 39 covers steering, and page 40 details changing turn. These pages are where a lot of operators get tripped up. The manual explains how the power steering system responds and what happens if you lose hydraulic pressure. It also covers the winch controls on page 37 – drum rotation control lever is on page 36 (note the page numbering order – always check the TOC). I’ve watched shop owners send green operators into a dozer without reading these pages, and the first time they try to make a tight turn in soft ground, they stall the engine or spin the tracks off. Don’t be that shop owner.

Why This Operators Manual Beats Aftermarket Reprints

I’ve got a shelf full of aftermarket manuals that claim to cover the 1150D. They skip the Cold Iron Parts warning, they omit the spark arrestor requirements, and they use generic illustrations that don’t match your machine. This factory manual – original 1995 print, 120 pages – has the exact decal placements, the correct lever diagrams, and the safety warnings that Case engineers wrote. If you need a parts catalog or service manual, see your Case dealer. For operation, this is the only source you trust. You can also check out related factory manuals like Case SL1-b, SL2 1995 Operators Manual – Factory Specs”>Case SL1-b, SL2 1995 Operators Manual – Factory Specs or Case SV212, SV216, SV208, SV210, SV223 Operators Manual – 214 Pages”>Case SV212, SV216, SV208, SV210, SV223 Operators Manual – 214 Pages. For another crawler option, see Case SV212 SV216 1994 Operators Manual – Factory Specs”>Case SV212 SV216 1994 Operators Manual – Factory Specs.

If you’re running a Manual Transmission”>manual transmission in your shop truck, you know the difference between a generic explanation and the factory book. Same thing here. And if you’re teaching a new operator, hand them this manual first – before they touch a lever. The Manual Transmission”>manual transmission example is just one of many reasons I refuse to trust anything but OEM documentation.

Does the Manual Cover Winch Controls?

Yes. Winch controls appear on page 24 (Winch Controls) and page 36 (Control Lever for Drum Rotation) and page 37 (Winch Controls again). The manual explains drum rotation, free-spool, and braking. If you’re running a winch-equipped 1150D, you need these pages memorized. One wrong lever pull and you’ll wrap cable around the idler. I’ve seen it.

3 Things to Check Before You Operate

First, page 5 – After Delivery Check. Second, page 13 – Maintenance checks. Third, page 17 – Spark Arrestor condition. That’s three minutes of reading that can prevent a fire or a breakdown. The manual doesn’t let you skip them, and neither should you.

How many pages does this manual have?

120 pages, including the full safety section and operating instructions.

Is this manual specific to the 1150D and 1155D, or does it cover other models?

It covers both the 1150D and 1155D crawlers. The TOC lists loader and dozer controls for both, but the winch and ripper sections are generic. If you need a manual for a different series, look at the related models above. The 120 pages are tailored to these two machines – no generic filler. Every illustration, every warning, every spec is for the 1150D/1155D. I’ve cross-checked the TOC against the actual pages, and there’s nothing for other models. If someone tells you this covers a 1150C, they’re wrong. Buy the right manual.

Bottom line: This is the factory book. No reprint, no photocopy, no third-party compilation. 120 pages of Case engineering from 1995. You need to operate a 1150D or 1155D safely? Access the Factory Manual and put it in the cab. Read it before you start the engine. That’s not a suggestion – that’s page 5.