Description

Ammann Rammax 1575 2014 Workshop Manual

If you’ve ever tried to rebuild a vibratory roller without factory torque numbers, you know the drill – guess the bolt tension, cross your fingers, and hope the drum doesn’t walk off the frame next week. That’s why I keep a copy of the Ammann Rammax 1575 2014 Workshop Manual within arm’s reach at the shop. This is not a generic reprint; it’s the OEM document from Ammann Schweiz AG, written for service fitters who need the exact procedure, not a suggestion.

Target Audience and Purpose

Page 12 spells it out: the manual is aimed at service fitters working in the field or in a shop. If you own a Rammax 1575 and plan to do anything beyond greasing zerks, you are the target audience. The manual covers maintenance, repair, and machine description – but it does not replace the operating manual. That means you still need the operator’s guide for daily checks, but for anything requiring a wrench or a multimeter, this is your document.

Product Description and Machine Identification

Chapter 2 gives you the full product data, including dimensions (page 19) and specifications. You get the machine type Rammax 1575, the Yanmar engine plate location (page 22), and the chassis number position (page 21). No more hunting for serial number stamps; the manual shows you exactly where to look. If you’re sourcing parts, the rating plate location is on page 20. Pair this manual with the Ammann Rammax 1575 Spare Parts Catalog to cross-reference part numbers.

Warnings: Not Optional Reading

Section 1.2.2 (page 14) dedicates a full page to warnings. Ammann takes safety seriously – there are specific cautions for hydraulic pressure, pinch points, and hot surfaces. I’ve seen rookies skip these and pay for it with busted fingers. Read them. The manual also covers orientation on the roller (page 13) so you know left from right when the manual says “left-hand side.”

310 Pages – What You Actually Get

Three hundred ten pages of factory data. That includes the general information chapter (page 11 onward), the product description, and – importantly – the structure of the workshop manual itself. The manual tells you how to use it, which is something aftermarket PDFs never do. Want to know if a procedure applies to your serial number? The scope section on page 12 clarifies that this manual covers serial number 61005 and up. No guesswork.

Does This Manual Cover the Fuel System?

Yes, it covers the entire Yanmar engine system as installed on the Rammax 1575. The product data chapter includes specifications for the engine, and the repair procedures later in the manual address fuel injection timing, injector removal, and more. If you need to service the Manual Transmission that connects the engine to the drive, the manual includes that too. For a deeper dive on manual transmission theory, check Manual Transmission on wikipedia – but for the actual bolt torque and shim specs, this workshop manual is what you want.

Torque Specs and Fluid Capacities

The manual provides factory torque values throughout each repair procedure. You won’t find a single “tighten securely” – every fastener has a number. For the drum mounts, the wheel lug nuts, the engine mounting bolts – it’s all there. Fluid capacities for the hydraulic tank, engine oil, and gearbox are listed in the specifications on page 19. Note: all values are metric, so keep a conversion chart handy if you’re used to lb-ft. I’d rather see you convert than strip a thread because you thought “hand tight” was close enough.

Source Authenticity – Why OEM Matters

This is a factory original from Ammann, not a scan of a scan. The Book ID is 1263968, published February 20, 2014. Aftermarket manuals often omit the warning labels, omit torque sequences, and sometimes even swap bolt grades. Ammann Schweiz AG wrote this for their own dealers. If you want to keep the roller in spec, you use their data. Period. For other Ammann models, see the Ammann AC70 AC110 Workshop Manual – Factory OEM Roller Repair Guide or the Ammann AV12-2 AV16-2 AV20-2 AV1-2 AV2-2 2006 Workshop Manual.

FAQ

Does this manual cover the Yanmar engine torque specs?

Yes.

What about wiring diagrams and hydraulic schematics?

The manual includes electrical and hydraulic schematics in the respective chapters. For the Rammax 1575, the wiring diagram covers the start circuit, vibratory motor control, and instrument panel. The hydraulic schematics show the charge pressure circuit, steering, and drum drive. All components are labeled with part numbers for easy cross-reference with the spare parts catalog. You will find the diagrams after the product description section – they are not just generic reference drawings but actual factory prints with wire colors and pin numbers.

Bottom line: if you work on compaction equipment, you need factory data. This 310-page Workshop Manual gives you the same information an Ammann dealer tech uses. Don’t waste time chasing bad specs. Access the Factory Manual from AutoRepairManuals and get the job done right.